Celestron FirstScope Signature Series Moon by Robert Reeves Telescope FirstSco - Page 1
Celestron FirstScope Signature Series Moon by Robert Reeves Telescope Manual
View all Celestron FirstScope Signature Series Moon by Robert Reeves Telescope manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
INSTRUCTION MANUAL - MODEL #22016 This manual covers basic instructions. For more detailed instructions, information, please visit celestron.com. 1 2 3 4 6 5 1. Thumbscrew 2. Eyepiece 3. Focuser 4. Focus Knob 5. Tube End 6. Optical Tube Your telescope is ready to use right out of the carton. Two eyepieces are included - 20 mm (15 power), and 4 mm (75 power). Remove the lens cap from the front of the optical tube before searching for objects. INSTALLING THE EYEPIECES An eyepiece is an optical element that magnifies the image focused by the telescope. It fits directly into the focuser (after removing the cap). Make sure the thumbscrews are not protruding into the focuser tube. Then, insert the chrome barrel of the eyepiece into the focuser and tighten the thumbscrews, being careful not to overtighten. Locate objects with the low power eyepiece (15x). Once you've centered your object, you can change to the higher power eyepiece (75x) for more magnification. The eyepieces can be changed by reversing the procedure described above. POINTING THE TELESCOPE The telescope is designed to be used on a table or other flat, sturdy surface. The FirstScope is easy to move wherever you want to point it. Turn counterclockwise to loosen the lock nut and hold the tube end. Sight along the optical tube towards the object you want to find. Move the tube end until you find the object you are searching for and then tighten the lock nut. IMAGE ORIENTATION When looking through the eyepiece from the rear or side of the optical tube (natural position), your image will be inverted (upside down and backwards) or angled. If you view from the front (slightly to either side) of the optical tube, the image will be correct. Use this technique for looking at terrestrial subjects. FOCUSING Simply turn the focus knob until the object comes in sharp. Turning the knob clockwise allows you to focus on an object that is farther than the one you are currently observing and vice versa. You will have to refocus after changing eyepieces. BONUS MATERIALS Your FirstScope includes a free download of Robert Reeves' ebook, Lunar Landscapes. Visit www.celestron.com/ robertreeves to access the PDF. The box that your FirstScope came in has a map of the lunar surface on the back. Cut it out and store it with your telescope so you can refer to it during future lunar observations. SOLAR WARNING Never look directly at the sun with the naked eye or with a telescope (unless you have the proper solar filter). Permanent and irreversible eye damage may result! FRANÇAIS GAMME SIGNATURE FIRSTSCOPE ROBERT REEVES LA LUNE GUIDE DE L'UTILISATEUR • MODÈLES N°. 22016 Ce mode d'emploi couvre les instructions de base. Pour obtenir des instructions plus détaillées et des informations supplémentaires, visitez celestron.com. 1. Vis 4. Dispositif de mise au point 2. Oculaire 5. Extrémité du tube 3. Bouton de mise au point 6. Tube optique Votre télescope est prêt à l'utilisation dès la sortie du carton. Deux oculaires sont inclus: 20mm (puissance de 15), et 4mm (puissance de 75). Enlevez le protège-objectif de l'avant du tube optique avant de commencer à observer. INSTALLATION DES OCULAIRES L'oculaire est un élément optique qui grossit l'image focalisée par le télescope. Il s'installe directement sur le dispositif de mise au point (après retrait du cache). Vérifiez que les vis moletées ne dépassent pas dans le tube du dispositif de mise au point. Insérez ensuite le barillet chromé de l'oculaire dans le tube de mise au point, puis serrez les vis moletées, en veillant à ne pas serrer excessivement. Localiser des objets avec l'oculaire de plus basse puissance (15x). Une fois l'objet centré, vous pouvez basculer sur un oculaire de plus grande puissance (75x) pour agrandir encore plus l'image. Il est possible de changer les oculaires en inversant la procédure décrite ci-dessus. POINTAGE DU TÉLESCOPE Le télescope est conçu pour être utilisé sur une table ou une autre surface plane et solide. Il est facile de déplacer le FirstScope sur le lieu depuis lequel vous souhaitez observer. Faites tourner la molette dans le sens inverse des aiguilles d'une montre et tenez l'extrémité du tube. Regardez dans la longueur du tube vers l'objet que vous souhaitez trouver. Déplacez l'extrémité du tube jusqu'à ce que vous trouviez l'objet que vous recherchez et serrez la molette. ORIENTATION DE L'IMAGE Lorsque vous regardez dans l'oculaire depuis l'arrière ou le côté du tube optique (en position naturelle), votre image sera inversée (verticalement et horizontalement), ou visible selon un angle différent. Si vous regardez depuis l'avant (en vous décalant légèrement d'un côté ou de l'autre) du tube optique, l'image sera correcte. Utilisez cette technique pour observer des objets terrestres. MISE AU POINT Tournez la molette de mise au point jusqu'à l'obtention d'une image nette. Le fait de faire tourner la molette dans le sens horaire vous permet de faire la mise au point sur un objet qui est plus loin que celui que vous observez actuellement, et vice-versa. Vous aurez besoin de refaire la mise au point après changement des oculaires. LITTÉRATURE EN BONUS Votre FirstScope est livré avec un téléchargement gratuit du livre électronique de Robert Reeves, Paysages lunaires. Visitez www.celestron.com/robertreeves pour accéder au fichier PDF. La boîte contenant votre FirstScope comporte une carte imprimée de la Lune sur l'arrière. Découpez-la et rangez-la avec votre télescope de manière à ce que vous puissiez vous y référer lors d'observations futures. AVERTISSEMENT SUR LE SOLEIL Ne regardez jamais directement le soleil à l'œil nu ou avec un télescope (à moins d'utiliser un filtre adapté.) Des dommages oculaires permanents et irréversibles peuvent être encourus. DEUTSCH SIGNATURE SERIES FIRSTSCOPE ROBERT REEVES MOND BEDIENUNGSANLEITUNG • MODELL-NR. 22016 Diese Betriebsanleitung enthält grundlegende Hinweise. Für weitere ins Detail gehende Informationen besuchen Sie bitte celestron.com. 1. Flügelschraube 2. Okular 3. Fokussierer 4. Fokussierknopf 5. Tubusende 6. Optischer Tubus Das Teleskop ist gebrauchsfertig vormontiert verpackt. Im Lieferumfang sind zwei Okulare enthalten: 20 mm (15x) und 4 mm (75x). Entfernen Sie vor dem Beobachten von Objekten den Objektivdeckel vorne am optischen Tubus. OKULARE AUFSETZEN Das Okular ist ein optisches Element, das das vom Teleskop fokussierte Bild vergrößert. Es passt direkt in den Fokussierer (nach dem Entfernen der Kappe). Achten Sie darauf, dass die Rändelschrauben nicht in den Fokussiertubus ragen. Stecken Sie dann die Chrom-Steckhülse des Okulars in den Fokussiertubus und ziehen Sie die Rändelschrauben fest, nicht zu fest ziehen. Lokalisieren Sie Objekte zuerst mit dem Okular von geringer Vergrößerungsleistung (15x). Sobald Sie Ihr Objekt zentriert haben, können Sie zum Okular mit höherer Vergrößerungsleistung (75x) wechseln. Die Okulare können durch Umkehren des oben beschriebenen Vorgangs gewechselt werden.