Clifford Concept 600 Owners Guide - Page 12
Table of User-Selectable Features - valet code
View all Clifford Concept 600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
EXAMPLE: Turn on Lock upon AutoArming and turn off Remote Valet Mode and FACT: In the following example, we will change the settings of three different features in just one programming session: We will turn on the Lock upon AutoArming feature to set your vehicle's power locks to automatically engage whenever the system AutoArms, turn off remote controlled valet mode and turn off the FACT anti-falsing feature: 1. Enter program mode as previously noted (ignition on, enter your valet code, press and hold the ✱ button on the PlainView 2 switch until you hear a chirp). 2. Since the Lock upon AutoArming feature is in column 3, row 2 of the Table, go to column 3 by pressing the blank button on the PlainView 2 switch three times. Wait for the 3-chirp/column 3 confirmation. Then press the ✱ button twice (you'll hear a chirp each time you press the ✱ button). After a brief pause, you'll hear 2 chirps to confirm that Lock upon AutoArming is now on. 3. Since FACT is also in column 3, there is no need to reselect column 3. Therefore, you can go straight to the row selection. Select row 4 by pressing the ✱ button four times. After a brief pause, you'll hear one chirp to confirm that FACT is now off. 4. You'll note that the Remote valet mode feature is at column 2, row 3. To change to column 2, press the blank button twice, then wait for the 2-chirp/column 2 confirmation. Press the ✱ button three times to select row 3. After a brief pause, you'll hear one chirp to confirm that the Remote valet mode feature is now turned off. 5. To exit the program mode, turn the ignition off. You'll hear 3 chirps to confirm program mode exit. Reset All Features If you wish to reset all the user-selectable features to their normal factory presets, you can do so simply by choosing the Reset all features selection (column 1, row 7) on the Table of User-Selectable Features. If you do so, all features - except the programmed remote controls and your valet code - will be reset to the factory settings that are indicated in BOLD type on the Table of User-Selectable Features. To reset all remote controls, use the Clear all remotes feature in column 2, row 6. To reset your valet code, use the Set a new valet/disarming PIN code feature in column 2, row 7. Table of User-Selectable Features Feature Select 1 blank press 2 blank presses 3 blank presses 4 blank presses 1 ✱ press Add master remote control NOTE 1 Chirps: off/loud/quiet (1/2/3 chirps) AutoArming: off/on NOTE 6 - Add companion remote: arm/disarm (1 then 2 chirps) 2 ✱ presses Personalized Siren Sounds** NOTE 2 SilentNight: off/on Lock upon AutoArming: off/on NOTE 7 - Add companion remote: trunk release* (2 chirps) 3 ✱ presses Play Personalized Siren Sounds**: trigger only/always (1/2 chirps) Valet mode entry/exit via the remote control: off/on AutoArming entry delay: off/on NOTE 7 - Add companion remote: silent arm and disarm (3 chirps) 4 ✱ presses Siren duration: 30/60/90sec.** AutoStart*: both off/both on/temp (1/2/3 chirps) only/battery only (1/2/3/4 chirps) FACT: off/on NOTE 7 - Add companion remote: timed headlight activation* (4 chirps) 5 ✱ presses AutoLock: off/on BlackJax anti-carjacking: off/on Headlight duration: 1sec. - 4.25 min. (10sec.) NOTE 5 NOTE 7 - Add companion remote: remote engine starting* (5 chirps) 6 ✱ presses AutoUnLock: off/on Clear all remotes NOTE 3 NightVision: off/on/on without postparking illumination (1/2/3 chirps) NOTE 7 - Add companion remote: window rolldown/venting* (6 chirps) 7 ✱ presses Reset all features (except remotes Set a new valet/disarming PIN code and valet code) to factory settings NOTE 4 NightVision activation: lighter/ twilight/darker (1/2/3 chirps) NOTE 7 - Add companion remote: remote valet mode (7 chirps) * Requires optional wiring or accessory; ask your Clifford Dealer for details. **Not available on European models in compliance with EC95/56 NOTE 1: Press button 1 of the new MASTER 5-button remote control. You will hear one chirp. Immediately press button 1 again. You will hear two chirps to confirm that the new remote control has been added. NOTE 2: Selection of this feature will cause the system to sound a few seconds of siren sound #1. Press the blank button to turn on this sound or the ✱ button to turn it off. The system will then sound a few seconds of sound #2. Repeat: blank=ON, ✱=OFF for each of the six sounds. NOTE 3: You'll hear two chirps to indicate all remotes have been cleared from memory. You must now add new/existing remotes with the "Add master remote control" feature and/or the "Other vehicle's remote" feature. NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the ignition (you'll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then re-enter your new PIN code. If the LED flashes on, your new code has been accepted. If the LED does not light, the two codes did not match and the system has reverted to your previous code. NOTE 5: The timer starts when you select this feature. When the duration you wish has been reached, press the blank button on the PlainView 2 valet switch (you'll hear 2-chirps) NOTE 6: Lets you arm/disarm with a new companion remote control or ANY remote (including 5-button master type) of a Clifford G4 system on your other vehicle(s). For instance, to set button ✱ of the other car's companion remote to arm and disarm your Concept 600, select column 4, row 1, then press button ✱ of the other vehicle's remote (you'll hear one chirp). Immediately press button ✱ a second time (you will hear a 2-chirp confirmation). Button ✱ of the other vehicle's remote will now arm/disarm your Concept 600 on this vehicle. NOTE 7: The features in this column allow you to control your system with the remote control of a G4 system on your