Clifford IntelliGuard 750 Owners Guide
Clifford IntelliGuard 750 Manual
 |
View all Clifford IntelliGuard 750 manuals
Add to My Manuals
Save this manual to your list of manuals |
Clifford IntelliGuard 750 manual content summary:
- Clifford IntelliGuard 750 | Owners Guide - Page 1
Intelliguard 750 Owner's Guide - Clifford IntelliGuard 750 | Owners Guide - Page 2
limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an - Clifford IntelliGuard 750 | Owners Guide - Page 3
WARRANTY TO REPLACE OR REPAIR Service at 1-800-876-0800. Directed security systems installed on automobile z Installation receipts important! Please note that this manual was intended for US consumers and therefore includes American phrases or words. trademarks and copyrights Bitwriter™, Clifford - Clifford IntelliGuard 750 | Owners Guide - Page 4
) . . . . .17 high frequency 18 smart power up II 18 power saver mode 18 programming options 19 cliffnet wizard installation software programming . . . . .21 manual programming instructions 21 user selectable features . . . . .23 user selectable features descriptions - column one . . .24 user - Clifford IntelliGuard 750 | Owners Guide - Page 5
dealers are provided with preprinted dealer certificates. In order to maximize the use of this system, please review this owner's guide carefully prior to using your system. You can print additional or replacement copies of this owner's guide by accessing the Clifford website at www.clifford.com. 2 - Clifford IntelliGuard 750 | Owners Guide - Page 6
remote is powered by a miniature 3V lithium battery that will last approximately one year under normal use. When the battery weakens, operating range will be reduced and the system proof of purchase, which reflects that the product was installed by an authorized dealer. fcc/id notice This device - Clifford IntelliGuard 750 | Owners Guide - Page 7
Disarm and Panic Button Trunk Release or Optional Accessory Channel Button note: This manual describes the features and accessories that are included with your system along with information about compatible Clifford accessories that are not included. For a list of included accessories, please refer - Clifford IntelliGuard 750 | Owners Guide - Page 8
learn the remote buttons. This makes it possible to assign any remote button to any system function. The remote initially comes programmed with standard configuration, but may also be customized using the CliffNet Wizard PC program. The buttons in all of the instructions in this manual correspond to - Clifford IntelliGuard 750 | Owners Guide - Page 9
These buttons adjust the dual-zone radar sensor. using your system The buttons used in the instructions in this manual correspond to the standard remote configuration. If your remote has been custom configured, the icons on your remote buttons may not correspond to the indicated functions. 6 - Clifford IntelliGuard 750 | Owners Guide - Page 10
will flash twice five seconds after the last door has been closed. The system is not actually armed at that point. The system arms and the doors lock (if connected and programmed for passive locking) at 30 seconds, but the siren will not chirp. The early chirps provide you with a 25-second warning - Clifford IntelliGuard 750 | Owners Guide - Page 11
to the Diagnostics section of this guide. This is called Tamper Alert. If the siren is active when the system is disarmed you will hear two chirps but the system is not disarmed. (Refer to the Remote Siren Silencing section of this guide.) However, if the alarm completes the full trigger cycle - Clifford IntelliGuard 750 | Owners Guide - Page 12
the installer for the location of the PlainView 2 Valet® button. Please refer to the Disarm/Valet® Mode section of this guide for instructions to enter the pin code. remote siren silencing This system offers remote siren silencing. Remote siren silencing is a fea- ture that makes it possible to - Clifford IntelliGuard 750 | Owners Guide - Page 13
a command to start the vehicle via the Intellistart, it bypasses sensor zones and will continue to bypass these zones until the remote start shuts down. When the system sees a SmartWindows command for up or down operation, the unit will automatically bypass sensor zones one, two, three, and eight - Clifford IntelliGuard 750 | Owners Guide - Page 14
you are threatened in or near your vehicle, you can attract attention by triggering the system with your remote! Just press for two seconds to enter Panic Mode. The siren will sound and the parking lights will flash for the programmed duration. If the ignition is on, the doors will lock; if the - Clifford IntelliGuard 750 | Owners Guide - Page 15
digit of the pin code is entered: a. To disarm the system: press and release . b. To enter valet® mode: Press section refer to remote buttons. Remember, the buttons used in all the instructions in this guide correspond to a Standard Configuration remote. This may not be how your remote is set up - Clifford IntelliGuard 750 | Owners Guide - Page 16
The siren will chirp once to confirm auto arming bypass. 3. The system will not auto arm. note: The system will revert to normal auto arming when the system sees autoactivate when using the remote to arm the system. low battery warning When the remote battery is low, the system will generate a low- - Clifford IntelliGuard 750 | Owners Guide - Page 17
covered by FACT II differently; if the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trig- ger ceases. FACT II is programmable. See the Programming Options section of this guide. note: Arming and disarming the system does not reset this function! The - Clifford IntelliGuard 750 | Owners Guide - Page 18
please refer to the selectable siren sounds fea- ture in the User Selectable Features grid. Once in programming mode, press on the remote to begin playback of and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred - Clifford IntelliGuard 750 | Owners Guide - Page 19
was involved when you turn the ignition on (see the Table of Zones section). The system will retain this information in its memory. Refer to the Multiple Event Total Recall section of this guide. arm/disarm diagnostic chart Action Arm Arm Chirps 2 4 Light Flashes 2 4 Arm 2 (5 sec.) 4 2 (5 sec - Clifford IntelliGuard 750 | Owners Guide - Page 20
system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed the receiver and remotes each use a mathematical formula called an algorithm to change their code each time the remote is used. - Clifford IntelliGuard 750 | Owners Guide - Page 21
to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet® Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be - Clifford IntelliGuard 750 | Owners Guide - Page 22
options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labor. Following is a list of the program settings, with the factory settings in bold: z Active arming (only with the remote) or passive arming - Clifford IntelliGuard 750 | Owners Guide - Page 23
, programming FACT II off may cause your system to violate state laws. z Siren tones and chirp volume: The output of the siren consists of six different tones in sequence and the arm/disarm chirp volume can be changed or eliminated. z Reset the system to all factory defaults. z Add or remove remote - Clifford IntelliGuard 750 | Owners Guide - Page 24
programming grids and lengthy programming sequences. For a complete guide to system programming using the Cliffnet Wizard refer to the Cliffnet Wizard help menu. manual programming instructions times as the desired column. After a pause the siren will chirp the same number of times as the selected column for - Clifford IntelliGuard 750 | Owners Guide - Page 25
at step 4 within 60 seconds. note: Refer to the Feature Descriptions sections of this guide for important notes and descriptions of the system features and programming. 7. Exit programming - To exit programming mode turn the ignition off or wait 60 seconds without pressing the PlainView 2 Valet - Clifford IntelliGuard 750 | Owners Guide - Page 26
Set PIN code (default = 2) New remote learn arm/disarm only Select siren sounds New remote learn accessory A channel FACT II off/on New remote learn accessory B channel Remote valet off/on New remote learn silent mode Entry delay off/on New remote learn remote valet Reset to default New - Clifford IntelliGuard 750 | Owners Guide - Page 27
until you hear a confirmation chirp. Press again until you hear two chirps indicating the new remote is learned. auto (passive) arm - off/on z Off: The remote must be used to arm the system. z On: When the system sees the ignition turn off and the last protected entry (door, hood, or trunk) close - Clifford IntelliGuard 750 | Owners Guide - Page 28
passively arms. This feature only applies when passive arming is programmed on. siren duration - 30/60/90 z The system will sound the alarm for the programmed duration (30/60/90 seconds) during an alarm trigger or when the system is put into panic mode. second unlock - off/on z Off: Second unlock - Clifford IntelliGuard 750 | Owners Guide - Page 29
personal PIN code. For more information, please refer to the PIN Programming section of this guide. select siren sounds The individual sounds the siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger. For more information, please refer to the Select - Clifford IntelliGuard 750 | Owners Guide - Page 30
reset to default settings All system settings (except PIN and remote programming) in the User Programming grid will be reset to their default factory setting as indicated in bold lettering. z Press the arm/disarm button of the TX; the siren will chirp twice as confirmation. panic off/on z Off: The - Clifford IntelliGuard 750 | Owners Guide - Page 31
output. accessory b output The remote channel programmed into this feature will activate the accessory output. silent mode The remote channel programmed into this feature will arm/disarm the system, but the siren will not chirp. remote valet® The remote channel programmed into this feature will make - Clifford IntelliGuard 750 | Owners Guide - Page 32
. This feature is convenient for erasing any remotes that have been lost, stolen, or incorrectly programmed into the system. z After entering this feature press any button on the remote; the siren will chirp to indicate that all remotes have been erased from memory. © 2004 directed electronics - Clifford IntelliGuard 750 | Owners Guide - Page 33
the feature location in the installer programming grid. 2. Immediately press and release of the PlainView 2 Valet button. 3. Select each digit by pressing 1-9 times, and then press to enter the number into the system. To enter a zero, press only. 4. Wait for two siren chirps after a five second - Clifford IntelliGuard 750 | Owners Guide - Page 34
the programming sequence. auto-immobilization feature Auto-immobilization is a feature designed for maximum security; it activates the UltraSecure Immobilization circuitry automatically. auto-immobilization sequence 1. Turn ignition off or disarm alarm. 2. After 30 seconds the systems Immobilization - Clifford IntelliGuard 750 | Owners Guide - Page 35
system to be put in valet mode only until the next time the ignition is turned on. ON: Valet mode will be exited every time the ignition is turned on. OFF: Valet mode will only be exited by using the valet button or the remote control. blackjax feature Clifford will activate the siren and brake - Clifford IntelliGuard 750 | Owners Guide - Page 36
the thief and vehicle. At this time your remote will not operate the system, only you can turn off the BlackJax by entering your secret PIN through the PlainView 2 valet button. blackjax activation sequence When BlackJax is programmed ON, BlackJax sequence will begin every time the ignition - Clifford IntelliGuard 750 | Owners Guide - Page 37
½ times idle or lower, the system will immobilize the vehicle as described in step 7. 7. Vehicle Immobilization: z Immobilizer will engage the starter and ignition circuits. z The siren will continue to sound and the should not know your PIN code (IE: valet parking, auto service department). 34 - Clifford IntelliGuard 750 | Owners Guide - Page 38
Operation 1. Turn ignition on. 2. Enter Pin code. 3. Within 10 seconds press . 4. Siren chirps 2 times as confirmation of BlackJax active. 5. Turn ignition off, siren chirps 3 times as confirmation of exiting programming. note: If ignition remains on after entering PIN code and no action for - Clifford IntelliGuard 750 | Owners Guide - Page 39
system 2. Transmit Channel 15 (Press 1 time). 3 times then z The LED will turn on and the siren will chirp 1 time. z Sensor test and adjustment mode is entered. 3. To test Primary (full trigger) zone. z Press of the remote control. z Siren will chirp 2 times. z Hit vehicle. z Siren - Clifford IntelliGuard 750 | Owners Guide - Page 40
level of impact. z Sensor adjusts itself to the force of Hit. z Siren chirps 1 time as confirmation of adjustment. z Press of the remote control to lock adjustment. 5. To enter Warn-away zone adjustment z Press . z Siren chirps 1 time. z Warn-away zone adjustment is entered. 6. To test - Clifford IntelliGuard 750 | Owners Guide - Page 41
as described in step 4. z Or press again to exit programming mode. z The siren will chirp 3 times when sensor adjustment mode has been exited. is used to indicate the status of your system. It is also used to report triggers and faults in the system or sensors. UltraSecure Immobilizer: A feature - Clifford IntelliGuard 750 | Owners Guide - Page 42
mode. Siren: Noise generating device usually installed in the engine compartment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the six tones you hear while the alarm is triggered. Remote: Hand-held transmitter which operates the various functions of your system - Clifford IntelliGuard 750 | Owners Guide - Page 43
. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the immobilization circuits active if Remote Start System: For the ultimate in convenience, the IntelliStart remote start system can start your vehicle, monitor engine functions, and power your climate control system - Clifford IntelliGuard 750 | Owners Guide - Page 44
recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. note: There may be a small charge incurred for this service. © 2004 directed electronics, inc - Clifford IntelliGuard 750 | Owners Guide - Page 45
The company behind this system is Directed Electronics, Inc. Since its inception, Directed® has are incompatible with some features. Directed® is committed to delivering world-class quality products and services that excite and delight our customers. Vista, CA 92081 www.directed.com © 2004 Directed
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
 |
 |
Intelliguard 750
Owner’s Guide