Craftsman 635LM Owners Manual

Universal Receiver

Model 635LM

OWNER’S MANUAL

INSTALLATION

•

Unplug the opener before proceeding.

•

OPEN RECEIVER: Insert a small screwdriver in slot on receiver

front panel as shown. Twist up actuator cover.

•

CONNECT RECEIVER AND OPENER: Remove about 1/4" of

insulation from each end of the 2-strand bell wire. Connect one

end to the receiver screw terminals (polarity is NOT required).

Route wire along the channels and out the bottom as shown.

•

Connect the other end of the bell wire to the two opener termi-

nals labeled “2” (white) and “1” (red), “common” and “command”

or the terminals used for the push button control.

•

Use insulated staples to secure bell wire between receiver and

opener. Length of bell wire depends on where the receiver will

be installed. Replace actuator cover.

•

Choose a 120Vac polarized outlet for the receiver which is

OUT

OF THE REACH OF CHILDREN. Plug receiver into selected

outlet. Return power to the opener.

REPLACEMENT PARTS:

Remote Control housing only

(no circuit board)

........................................................

41A5056-3

Visor clip

........................................................................

29B137

Lithium Battery

..................................................................

10A20

Universal Receiver (complete)

..................................

41A5041-2

Receiver Actuator Cover

..............................................

41A3591

Actuator Cover

"LEARN"

Indicator

Light

"LEARN"

Actuator

Terminals

Bell Wire

Channels

Connect Bell Wire

To Garage Door

Opener Terminals

Bell Wire

Power Indicator Light

Universal Receiver

"LEARN"

Actuator

Indicator Light

Security

Remote Control

Select a

push button

©2002, The Chamberlain Group, Inc.

114A2128C

All Rights Reserved

Printed in Mexico

NOTICE TO U. S. CONSUMERS:

Some states prohibit the service or repair of garage door openers which

cannot be made to comply with the safety standards contained in UL 325

(1988 revision). In order to comply with both the letter and the spirit of these

laws, this universal radio control should not be used with any LiftMaster

®

,

Chamberlain

®

, or Sears Craftsman

®

garage door opener manufactured

prior to April 1, 1982. To find out if your Chamberlain-made garage door

opener was manufactured prior to or after April 1, 1982, please call 1-800-

528-9131 before installing this universal radio control.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is not connected BEFORE installing the receiver.

To prevent possible SERIOUS INJURY or DEATH from a moving

gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

WARNING

NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiv-

er and/or transmitter are prohibited, except for changing the code setting or replacing the

battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

PROGRAMMING THE REMOTE TO THE

RECEIVER

With Security

, the code between the remote control and the

receiver changes with each use, accessing over 100 billion new

codes.

You can activate your opener with up to 8 Security

remote con-

trols and one Security

Keyless Entry.

1. Pry open the front panel of receiver case with a screwdriver.

Re-connect power to opener.

2. Press and release the “learn” actuator on the receiver. The

learn indicator light will glow steadily for 30 seconds.

3. Within 30 seconds, press and hold the button on the hand-held

remote that you wish to operate your garage door.

The opener will now operate when either the receiver actuator or

the remote control push button is pressed.

Repeat Steps 2 and 3 for each remote control that will be used to

operate the garage door opener.

TO ERASE ALL REMOTE CONTROL CODES

Press and hold the “learn” actuator on the receiver panel until the

indicator light turns off (about 6 seconds). All transmitter codes

are now erased. Then follow the steps above to reprogram each

remote control.

FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2806

Craftsman 635LM Owners Manual

Craftsman 635LM - Sears LiftMaster Chamberlain Manual

Craftsman 635LM manual content summary: