Craftsman 635LM Owners Manual - Page 1
Craftsman 635LM - Sears LiftMaster Chamberlain Manual
UPC - 753182407708
View all Craftsman 635LM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
WARNING WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. INSTALLATION • Unplug the opener before proceeding. • OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown. Twist up actuator cover. • CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. • Connect the other end of the bell wire to the two opener terminals labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. • Use insulated staples to secure bell wire between receiver and opener. Length of bell wire depends on where the receiver will be installed. Replace actuator cover. • Choose a 120Vac polarized outlet for the receiver which is OUT OF THE REACH OF CHILDREN. Plug receiver into selected outlet. Return power to the opener. PROGRAMMING THE REMOTE TO THE RECEIVER With Security✚, the code between the remote control and the receiver changes with each use, accessing over 100 billion new codes. You can activate your opener with up to 8 Security✚ remote controls and one Security✚ Keyless Entry. 1. Pry open the front panel of receiver case with a screwdriver. Re-connect power to opener. 2. Press and release the "learn" actuator on the receiver. The learn indicator light will glow steadily for 30 seconds. 3. Within 30 seconds, press and hold the button on the hand-held remote that you wish to operate your garage door. The opener will now operate when either the receiver actuator or the remote control push button is pressed. Repeat Steps 2 and 3 for each remote control that will be used to operate the garage door opener. TO ERASE ALL REMOTE CONTROL CODES Press and hold the "learn" actuator on the receiver panel until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to reprogram each remote control. Universal Receiver Model 635LM OWNER'S MANUAL NOTICE TO U. S. CONSUMERS: Some states prohibit the service or repair of garage door openers which cannot be made to comply with the safety standards contained in UL 325 (1988 revision). In order to comply with both the letter and the spirit of these laws, this universal radio control should not be used with any LiftMaster®, Chamberlain®, or Sears Craftsman® garage door opener manufactured prior to April 1, 1982. To find out if your Chamberlain-made garage door opener was manufactured prior to or after April 1, 1982, please call 1-800528-9131 before installing this universal radio control. Actuator Cover Power Indicator Light Terminals "LEARN" Indicator Light "LEARN" Actuator Bell Wire Channels Connect Bell Wire To Garage Door Opener Terminals Bell Wire Security✚ Remote Control Universal Receiver Select a push button Indicator Light "LEARN" Actuator NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. REPLACEMENT PARTS: Remote Control housing only (no circuit board 41A5056-3 Visor clip 29B137 Lithium Battery 10A20 Universal Receiver (complete 41A5041-2 Receiver Actuator Cover 41A3591 114A2128C FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2806 ©2002, The Chamberlain Group, Inc. All Rights Reserved Printed in Mexico