Cub Cadet Challenger 400LX Installation Manual - Page 1

Cub Cadet Challenger 400LX Manual

Get Cub Cadet Challenger 400LX PDF manuals and user guides View all Cub Cadet Challenger 400LX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Installation Sheet 39A70051100 One-Piece Windshield E E E D A C B F E E E Contents of Carton A. Windshield (Qty. 1) B. Lower Windshield (1) C. Windshield Seal, 37" (1) D. Windshield Seal, 47-3/4" E. Clamp Assembly (6) • Clamp • Nut • Bolt F. Lower Windshield Seal (1) Tools Required • Adjustable Wrench Figure 1 2. Using four (4) clamp assemblies (E), 3. mount the windshield (A) to the Operator Protective Structure (OPS) tube. Do not fully tighten the hardware yet. If a roof is equipped, be sure to slide the windshield (A) under the roof panel. The windshield seals to the roof using the windshield seal (D). Refer to Figure 3. Install the lower windshield (B) using the two remaining clamp assemblies (E) so that the lower windshield seal (F) rests on the hood. See Figure 4. B Figure 2 Installing the Windshield NOTE: The windshield and/or roof should be removed when trailering your unit. 1. Remove the clamps with the hardware installed (nuts and bolts) from the hardware pack. Then remove the hardware from the clamps. Bolt Rubber Grommet & Spacer E F Windshield OPS Tube Nut Figure 3 NOTE: Install the windshield on top of the clamp and not inside it. This in conjuction with the rubber grommet helps reduce cracking due to flexing of the frame and OPS. NOTE: Do not overtighten. Doing so could cause damage to the windshield. Figure 4 4. Tighten all the hardware but be careful not to overtighten. If you have difficulty assembling this product, have questions regarding the controls, operation, or maintenance of this product, want to order replacement parts/attachments/accessories; you can seek help from the experts. Have your full model number and serial number ready. Choose from the options below: Web: www.cubcadet.com/equipment/cubcadet/service-and-parts Phone: (800) 965-4CUB Mail: Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019 769-11590

  • 1
  • 2
Installation Sheet
39A70051100 One-Piece Windshield
If you have difficulty assembling this product, have questions regarding the controls, operation, or maintenance of this product, want to order
replacement parts/attachments/accessories; you can seek help from the experts. Have your full model number and serial number ready. Choose
from the options below:
Web:
www.cubcadet.com/equipment/cubcadet/service-and-parts
Phone:
(800) 965-4CUB
Mail:
Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
769-11590
A
E
E
F
B
C
D
E
E
E
E
Figure 1
Figure 2
Installing the Windshield
NOTE:
The windshield and/or roof should be
removed when trailering your unit.
1.
Remove the clamps with the hardware
installed (nuts and bolts) from the
hardware pack. Then remove the
hardware from the clamps.
Contents of Carton
A.
Windshield (Qty. 1)
B.
Lower Windshield (1)
C.
Windshield Seal, 37” (1)
D.
Windshield Seal, 47-°”
E.
Clamp Assembly (6)
•
Clamp
•
Nut
•
Bolt
F.
Lower Windshield Seal (1)
Tools Required
•
Adjustable Wrench
2.
Using four (4) clamp assemblies (E),
mount the windshield (A) to the
Operator Protective Structure (OPS)
tube. Do not fully tighten the hardware
yet. If a roof is equipped, be sure to slide
the windshield (A) under the roof panel.
The windshield seals to the roof using
the windshield seal (D). Refer to Figure 3.
Windshield
Rubber Grommet
& Spacer
Bolt
Nut
OPS Tube
Figure 3
NOTE:
Install the windshield on top
of the clamp and not inside it. This in
conjuction with the rubber grommet
helps reduce cracking due to flexing of
the frame and OPS.
NOTE:
Do not overtighten. Doing so
could cause damage to the windshield.
3.
Install the lower windshield (B) using
the two remaining clamp assemblies
(E) so that the lower windshield seal (F)
rests on the hood. See Figure 4.
E
B
F
Figure 4
4.
Tighten all the hardware but be careful
not to overtighten.