D-Link DGS-1210-10 Reference Guide - Page 45

L2 Functions > Link Aggregation > LACP Port Settings, L2 Functions > Multicast > IGMP Snooping

Get D-Link DGS-1210-10 PDF manuals and user guides View all D-Link DGS-1210-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

5 Configuration D-Link Web Smart Switch User Manual Figure 5.41 - L2 Functions > Link Aggregation > Port Trunking NOTE: Each combined trunk port must be connected to devices within the same VLAN group. L2 Functions > Link Aggregation > LACP Port Settings The LACP Port Settings is used to create port trunking groups on the Switch. The user may set which ports will be active and passive in processing and sending LACP control frames. Figure 5.42 - L2 Functions > Link Aggregation > LACP Port Settings From Port: The beginning of a consecutive group of ports may be configured starting with the selected port. To Port: The ending of a consecutive group of ports may be configured starting with the selected port. Activity: There are two different roles of LACP ports: Active - Active LACP ports are capable of processing and sending LACP control frames. This allows LACP compliant devices to negotiate the aggregated link so the group may be changed dynamically as needs require. In order to utilize the ability to change an aggregated port group, that is, to add or subtract ports from the group, at least one of the participating devices must designate LACP ports as active. Both devices must support LACP. Passive - LACP ports that are designated as passive cannot initially send LACP control frames. In order to allow the linked port group to negotiate adjustments and make changes dynamically, one end of the connection must have "active" LACP ports. Timeout: Specify the administrative LACP timeout. The possible field values are: Short (3 Sec) - Defines the LACP timeout as 3 seconds. Long (90 Sec) - Defines the LACP timeout as 90 seconds. This is the default value. Click Apply to implement the changes made. L2 Functions > Multicast > IGMP Snooping With Internet Group Management Protocol (IGMP) snooping, the Web Smart Switch can make intelligent multicast forwarding decisions by examining the contents of each frame's Layer 2 MAC header. IGMP snooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the Web Smart Switch will forward multicast traffic only to connections that have group members attached. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
5
Configuration
D-Link Web Smart Switch User Manual
Figure 5.41 – L2 Functions > Link Aggregation > Port Trunking
NOTE:
Each combined trunk port must be
connected to devices within the same VLAN
group.
L2 Functions > Link Aggregation > LACP Port Settings
The LACP Port Settings is used to create port trunking groups on the Switch. The user may set which ports
will be active and passive in processing and sending LACP control frames.
Figure 5.42 – L2 Functions > Link Aggregation > LACP Port Settings
From Port:
The beginning of a consecutive group of ports may be configured starting with the selected port.
To Port:
The ending of a consecutive group of ports may be configured starting with the selected port.
Activity:
There are two different roles of LACP ports:
Active -
Active LACP ports are capable of processing and sending LACP control frames. This allows
LACP compliant devices to negotiate the aggregated link so the group may be changed dynamically
as needs require. In order to utilize the ability to change an aggregated port group, that is, to add or
subtract ports from the group, at least one of the participating devices must designate LACP ports as
active. Both devices must support LACP.
Passive -
LACP po
d LACP control frames. In
order to allow the linked port group to negotiate adjustments and make changes dynamically, one
Click
A
2 Fun
rts that are designated as passive cannot initially sen
end of the connection must have "active" LACP ports.
Timeout:
Specify the administrative LACP timeout. The possible field values are:
seconds.
Short (3 Sec)
- Defines the LACP timeout as 3
Long (90 Sec)
- Defines the LACP timeout as 90 seconds. This is the default value.
pply
to implement the changes made.
ctions > Multicast > IGMP Snooping
L
With In
multica
IGMP s
Smart S
at have group members attached.
ternet Group Management Protocol (IGMP) snooping, the Web Smart Switch can make intelligent
st forwarding decisions by examining the contents of each frame’s Layer 2 MAC header.
nooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the Web
witch will forward multicast traffic only to connections th
40