D-Link DSL-2320B Product Manual
D-Link DSL-2320B - 24 Mbps DSL Modem Manual
 |
UPC - 790069298257
View all D-Link DSL-2320B manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DSL-2320B manual content summary:
- D-Link DSL-2320B | Product Manual - Page 1
- D-Link DSL-2320B | Product Manual - Page 2
-IP Address 40 Time 41 Remote Log 42 System 44 Save and Reboot 44 Backup Settings 44 Update Settings 45 Restore Default Settings 45 Firmware 46 Test 47 Status 48 Device Info 48 WAN Info 49 Route Info 49 Log 50 LAN 50 WAN 51 D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 3
of Contents ATM 52 ADSL 53 ADSL BER Test 54 Troubleshooting 56 Networking Basics 58 Check your IP address 58 Check your MAC address 58 Statically Assign an IP address 59 Contacting Technical Support 60 Warranty 61 Registration 63 D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 4
General Information The D-Link DSL-2320B is an ADSL2+ modem offering the convenience of both Ethernet and USB connections. This user manual provides you with a simple and easy-to-understand format to install and configure your modem. Package Contents • ADSL2/2+ Ethernet/USB Modem • 12VDC, 1A DC - D-Link DSL-2320B | Product Manual - Page 5
. A flashing LED indicates the modem is attempting to synchronize with the DSL provider. USB LED A Solid light indicates a connection is established using USB. A flashing LED indicates traffic is being send and received using USB. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 6
to an active telephone line (RJ-11). Power Receptor Receptor for the supplied power adapter. USB Port Connect a computer using a USB cable. Reset Pressing the Reset button restores the modem to its original factory default settings. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 7
to the modem. Connect one end of the USB cable to the USB port on the back of the modem and connect the other end to a free USB port on your PC. The Found New Hardware Wizard will open on your PC. See the Installation Diagram on page 9. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 8
power strip. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 9
Section 3 - Installation Diagram Installation Diagram D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 10
/XP operating system. The following pop-up window appears when you connect the USB cable to your computer (with the other end already attached to the modem). The Found New Hardware Wizard will appear on your screen. To continue, click Next. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 10 - D-Link DSL-2320B | Product Manual - Page 11
. The default selection is set to search for a suitable driver for my device (recommended). To contunue, click Next. Next, you can specify the search locations. Make sure CD-ROM drives and Specify a Location are selected and click Next. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 11 - D-Link DSL-2320B | Product Manual - Page 12
the file has been selected, the this screen will appear verifying the location where the file will be extracted from. Click on OK to continue. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 12 - D-Link DSL-2320B | Product Manual - Page 13
Section 5 - USB Installation This next screen shows the device and the driver to be installed. Click Next to proceed with the installation. The last screen confirms that the installation is complete. Click on Finish to close the wizard. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 13 - D-Link DSL-2320B | Product Manual - Page 14
(TCP/IP) does not appear as an installed component, then click on Install. 5. In the Select Network Component Type window, click on protocol and then the Add button. 6. Select Internet Protocol (TCP/IP) from the list and then click on OK. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 14 - D-Link DSL-2320B | Product Manual - Page 15
- Configuring Your IP address and type 192.168.1.x (where x is any number between 2 and 254) for the IP address field and 255.255.255.0 for the Subnet Mask field. 5. Click on OK twice to save your changes and then close the Control Panel. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 16
(username / password: support / support). Note: Passwords can be changed at any time. 3. Enter your user name and password, and then click OK to display the user interface. Note: This manual has been prepared using the admin user name. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 16 - D-Link DSL-2320B | Product Manual - Page 17
, click on the box labeled DSL Auto-connect, a process that will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To continue, click on the Next button. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 17 - D-Link DSL-2320B | Product Manual - Page 18
Section 7 - Home If you uncheck the DSL Auto-connect box, the resulting screen is seen below. Enter the VPI/VCI as indicated by your ISP. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 18 - D-Link DSL-2320B | Product Manual - Page 19
the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use. Connection types include PPPoA, PPPoE, and Bridging modes. Note: The following is a bridging example. Click on Next to continue. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 19 - D-Link DSL-2320B | Product Manual - Page 20
Section 7 - Home The Enable Bridge Service checkbox is selected by default with the bridge service name in the box. Click on Next to continue. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 20 - D-Link DSL-2320B | Product Manual - Page 21
Section 7 - Home The next screen displays the LAN IP address and subnet mask. Make any necessary changes and click on Next. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 21 - D-Link DSL-2320B | Product Manual - Page 22
are done, the WAN Setup Summary screen displays all WAN settings that you have made. Check that the settings are correct before clicking on the Save / Reboot button. Clicking on Save / Reboot will save your settings and restart your modem. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 22 - D-Link DSL-2320B | Product Manual - Page 23
the ATM PVC Configuration screen as seen here. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. Find out the following values from your ISP before you change them. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 23 - D-Link DSL-2320B | Product Manual - Page 24
Used by time-sensitive applications such as real-time video. Rt-VBR service Variable Bit Rate): allows the network more flexibility than CBR. Quality of Can be enabled only for UBR without PCR, UBR with PCR, and Non Realtime VPR. Service: D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 24 - D-Link DSL-2320B | Product Manual - Page 25
Section 7 - Home This screen shows the types of network protocols and encapsulation modes: • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • Bridging D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 25 - D-Link DSL-2320B | Product Manual - Page 26
address: issued IP address to connect to the Internet. If selected, you will be asked to enter the static IP address. Click Next when finished with your configurations and the below screen will follow displaying the WAN settings that you made. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 27
Section 7 - Home When satisfied with the settings click on the Apply button. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 27 - D-Link DSL-2320B | Product Manual - Page 28
the configurations, it will return to the WAN Setup screen showing the new configurations. Select the Finish button to save the changes and reboot the modem. This is the DSL Modem Reboot screen that will appear during the rebooting process. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 29
the LAN interface. The Save button only saves the LAN configuration data, but does not apply the configurations. Select the Save/Reboot button to save the LAN configuration data, then reboot the modem and apply the new configuration. LAN D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 29 - D-Link DSL-2320B | Product Manual - Page 30
Section 7 - Home Logout To log out of the modem's user interface at any time during the setup, click on the Logout button. A confirmation screen will appear confirming that you really want to log out. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 30 - D-Link DSL-2320B | Product Manual - Page 31
capability settings. Consult your ISP to determine the correct settings. Click Apply if you are finished or click on Advanced Settings if you want to configure other advanced settings. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 31 - D-Link DSL-2320B | Product Manual - Page 32
The test mode can be selected from the ADSL Advanced Settings page. Test modes include normal, reverb, medley, no retrain, and L3. After you make your selection, click on Apply to save these settings first before you go to Tone Selection. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 32 - D-Link DSL-2320B | Product Manual - Page 33
tone carries separate data, so the modem operates as if 256 separate modems were running in parallel. The tone range is from 0 to 31 for upstream and from 32 to 255 for downstream. Do not change these settings unless directed by your ISP. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 33 - D-Link DSL-2320B | Product Manual - Page 34
network devices that are configured for SNMP. To configure the SNMP agent select Enable, Enter a Read Community, Set Community, System Name, Location, Contact, and the IP address of the Trap Manager. To save the configuration click Apply. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 34 - D-Link DSL-2320B | Product Manual - Page 35
address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. If you click Change Policy, a confirmation dialog allows you to verify your change. Select Yes to continue, or No to to cancel. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 36
address, the necessary Frame Direction, and WAN interface (bridge mode only). Click Apply to save. After you save the settings, a screen showing the settings will appear. On this screen you will be able to view and delete MAC filtering rules. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 37
Setup Parental Control Time of Day Restrictions In a home setting, parents can disallow access to the modem address of a computer see "Networking Basics" in the Appendix section of this manual. Click Apply to save the settings and continue. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 38
the Admin button to change the modems account passwords. Click the Services button to configure what services are allowed to pass through the modem. Click the IP Address button to define who is permitted access to local management features. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 38 - D-Link DSL-2320B | Product Manual - Page 39
monitoring network devices. Telnet: A standard Internet protocol for accessing remote systems. TFTP: (Trivial File Transfer Protocol) A very simple form of the File Transfer Protocol (FTP). D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 39 - D-Link DSL-2320B | Product Manual - Page 40
username and password is supplied at log on. Enter the IP address of the management station permitted to access the local configuration and click Apply. This will return you to the previous screen where you can enable access control. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 40 - D-Link DSL-2320B | Product Manual - Page 41
. Select from the list of NTP (Network Time Protocol) time servers.Then select the time zone that you are in and click Apply to save. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 41 - D-Link DSL-2320B | Product Manual - Page 42
section (see screen on right). To return to the previous screen to configure system log, remember to click on the Tools tab (located on top row selected log level will be logged and displayed. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual System log when log is disabled. System log when - D-Link DSL-2320B | Product Manual - Page 43
be sent to a specified IP address and UDP port of a remote system log server. If the selected mode is "Local" or "Both", events will be recorded and viewed locally. Select the desired values and click Apply to save the system log options. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 43 - D-Link DSL-2320B | Product Manual - Page 44
on the modem, but would like to revert to a previous configuration. To save your current configuration, click the Backup Settings button. The following pop-up screen will appear with a prompt to open or save the file to your computer. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 44 - D-Link DSL-2320B | Product Manual - Page 45
and restore the modem to factory default settings. Click on the Restore Default Settings button to proceed. The following confirmation dialog will appear confirming your decision to restore default settings. Click on OK to continue. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 45 - D-Link DSL-2320B | Product Manual - Page 46
. 1. Obtain an updated software image file (firmware) from your ISP. 2. Enter the path of the image file location or click the Browse button to locate the image file. 3. Click the Update Software button once to upload the new image file. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 46 - D-Link DSL-2320B | Product Manual - Page 47
to your Internet service provider There are three buttons at the bottom of the page; Next Connection (appears only if you have created more than one connection), Test and Test with OAM F4 (which will allow you to retest if necessary). D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 47 - D-Link DSL-2320B | Product Manual - Page 48
status information for your modem's connection. Device Info The Device Info page shows details of the modem such as the version of the software, bootloader, LAN IP address, etc. It also displays the current status of your DSL connection. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 48 - D-Link DSL-2320B | Product Manual - Page 49
information, displaying either ADSL Link Down or ADSL Link Up. WAN Info Route Info The Route Info section displays route information showing the IP addresses of the destination, gateway, and subnet mask as well as other route information. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 49 - D-Link DSL-2320B | Product Manual - Page 50
This is the same screen as seen in the Remotelog section under tools. LAN The LAN section shows received and transmitted packet information for the Ethernet interface. Click on Reset Statistics to renew the information. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 50 - D-Link DSL-2320B | Product Manual - Page 51
Section 10 - Status WAN The WAN section shows received and transmitted packet information for the WAN connections that you have set up. Click on Reset Statistics to renew the information. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 51 - D-Link DSL-2320B | Product Manual - Page 52
Section 10 - Status ATM The ATM section displays statistical values for your ATM interface as well as for AAL5 and AAL5 VCC. Click on Reset Statistics to reset the values. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 52 - D-Link DSL-2320B | Product Manual - Page 53
Section 10 - Status ADSL Information contained in the ADSL screen is useful for troubleshooting and diagnosing connection problems. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 53 - D-Link DSL-2320B | Product Manual - Page 54
the length of time that the test will run for. At any time during the test, click on the Stop button to terminate the test. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 54 - D-Link DSL-2320B | Product Manual - Page 55
Section 10 - Status When the test is complete, the following window will display the test results showing the test time, total transferred bits, total error bits and error ratio. Click Exit to close the window. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 55 - D-Link DSL-2320B | Product Manual - Page 56
as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 56 - D-Link DSL-2320B | Product Manual - Page 57
modem powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the modem will go through its reboot process. Wait about 30 seconds to access the modem. For information about logging into the modem see page 16. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 58
the prompt, type ipconfig /all and press Enter. This will display information about all installed adapters on your computer. Your MAC address is listed as the "Physical Address" and should look like xx-xx-xx-xx-xx-xx or xx:xx:xx:xx:xx:xx D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 58 - D-Link DSL-2320B | Product Manual - Page 59
LAN IP address of your modem (192.168.0.1). Set Primary DNS the same as the LAN IP address of your modem (192.168.0.1).The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 59 - D-Link DSL-2320B | Product Manual - Page 60
issues. For customers within the United States: Phone Support: (877) 453-5465 (877) 45-DLINK Internet Support: http://support.dlink.com For customers within Canada: Phone Support: (800) 361-5265 Internet Support: http://support.dlink.com D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 60 - D-Link DSL-2320B | Product Manual - Page 61
D-Link Technical Support at dlink Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual - D-Link DSL-2320B | Product Manual - Page 62
firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link with the instructions, may cause Link office. D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 62 - D-Link DSL-2320B | Product Manual - Page 63
Appendix D - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.2 May 14, 2007 D-Link DSL-2320B ADSL2+ Ethernet/USB Modem User Manual 63
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
 |
 |
