Dell 1130 Mono User's Guide - Page 43

Labels, Card stock/Custom-sized paper, Letterhead/Preprinted paper, Adhesives, Arrangement, Condition

Get Dell 1130 Mono PDF manuals and user guides View all Dell 1130 Mono manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

To avoid fading, do not expose printed transparencies to prolonged sunlight. Ensure that transparencies are not wrinkled, curled, or have any torn edges. Do not use transparencies that separates from the backing sheet. To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are begin printed out. Labels To avoid damaging the machine, use only labels designed for use in laser machines. When selecting labels, consider the following factors: Adhesives: The adhesive material should be stable at your machine's fusing temperature about 170°C (338 °F). Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. Curl: Prior to printing, labels must lie flat with no more than 13 mm of curl in any direction. Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock/Custom-sized paper Postcards, cards and other custom-sized materials can be printed with this machine. Do not print on media smaller than 76 mm (3.00 inches) wide or 127 mm (5.00 inches) long. In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material. If media weight is over 160 g/m2 (43 lb), try printing in the rear cover (face up). Letterhead/Preprinted paper Tray1 Single-sided Face down Double-sided Face up Manual tray Face up Face down

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
To avoid fading, do not expose printed transparencies to prolonged sunlight.
Ensure that transparencies are not wrinkled, curled, or have any torn edges.
Do not use transparencies that separates from the backing sheet.
To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are begin
printed out.
Labels
To avoid damaging the machine, use only labels designed for use in laser machines.
When selecting labels, consider the following factors:
Adhesives:
The adhesive material should be stable at your machine’s fusing temperature about 170°C (338 °F).
Arrangement:
Only use labels with no exposed backing between them. Labels can peel off sheets that have
spaces between the labels, causing serious jams.
Curl:
Prior to printing, labels must lie flat with no more than 13 mm of curl in any direction.
Condition:
Do not use labels with wrinkles, bubbles, or other indications of separation.
Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off
during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components.
Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single
pass through the machine.
Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.
Card stock/Custom-sized paper
Postcards, cards and other custom-sized materials can be printed with this machine.
Do not print on media smaller than 76 mm (3.00 inches) wide or 127 mm (5.00 inches) long.
In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material.
If media weight is over 160 g/m
2
(43 lb), try printing in the rear cover (face up).
Letterhead/Preprinted paper
Single-sided
Double-sided
Tray1
Face down
Face up
Manual tray
Face up
Face down