Dell OptiPlex 5090 Small Form Factor Service Manual - Page 67

SATA power cable, SATA data cables

Get Dell OptiPlex 5090 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 5090 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Steps 1. Align and lower the system board into the system until the stand-off points at the back of the system board align with those on the chassis. 2. Replace the four screws (6-32) and the single standoff screw (M2X4) screw to secure the system board to the chassis. 3. Connect the following cables to the respective connectors on the system board: ● Intrusion switch ● ATX system board power supply cables ● Power button switch ● ATX CPU power supply cable ● SATA data cables ● SATA power cable ● System fan cable 4. Align and lower the I/O panel into the slot on the chassis. 5. Replace the screws (6-32) to secure the I/O panel to the chassis. Next steps 1. Install the processor. 2. Install the fan assembly. 3. Install the WLAN card. Removing and installing components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Steps
1.
Align and lower the system board into the system until the stand-off points at the back of the system board align with those
on the chassis.
2.
Replace the four screws (6-32) and the single standoff screw (M2X4) screw to secure the system board to the chassis.
3.
Connect the following cables to the respective connectors on the system board:
●
Intrusion switch
●
ATX system board power supply cables
●
Power button switch
●
ATX CPU power supply cable
●
SATA data cables
●
SATA power cable
●
System fan cable
4.
Align and lower the I/O panel into the slot on the chassis.
5.
Replace the screws (6-32) to secure the I/O panel to the chassis.
Next steps
1.
Install the
processor
.
2.
Install the
fan assembly
.
3.
Install the
WLAN card
.
Removing and installing components
67