Denon DCM-5001 Serial Protocol - Page 24

This command is enabled only when the system status is Disc Sense

Get Denon DCM-5001 PDF manuals and user guides View all Denon DCM-5001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

.14 Cross Fade Play This command starts reproduction in the Cross Fade Play mode. This command is valid only in the Cross Fade mode. This command can be used only when the Cross Fade mode is set and reproduction is required. Use the Cross Fade Disc Reserve command to reserve the next disc after the Cross Fade reproduction starts. bytebit 7 6 5 4 3 2 1 0 0 STX02h 1 Command code ('X') 2 Disc number (100 digits) 3 Disc number (10 digits) 4 Disc number (1 digits) 5 Track number (10 digits) 6 Track number (10digits) 7 Next disc number (100 digits) 8 Next disc number (10 digits) 9 Next disc number (1 digits) 10 Next track number (10 digits) 11 Next track number (1 digits) 12 ETX03h 13 BCCH (high-level) 14 BCCL (low-level) (1) Answers returned bytebit 7 6 5 4 3 2 1 0 0 STX02h 1 Reply code ('X') 2 Answer code 3 ETX03h 4 BCCH (high-level) 5 BCCL (low-level) (2) Special condition • Specify a disk number and a track number that are present and available as the parameters. The disc number (byte 2 to byte 4) must not be equal to the next disc number (byte 2 to byte 9). • This command is enabled only when the system status is Disc Sense Complete (3) and when the zone status is No Disc (A) or Stop (B). • In case the Cross Fade Disc Reserve command cannot be submitted as the command submission conditions are not satisfied (in the Auto Pause status), this command can starts cross fade reproduction. (3) Other

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
.14
Cross Fade Play
This command starts reproduction in the Cross Fade Play mode.
This command is valid only in the Cross Fade mode.
This command can be used only when the
Cross Fade mode is set and reproduction is required.
Use the Cross Fade Disc Reserve command
to reserve the next disc after the Cross Fade reproduction starts.
bytebit
7
6
5
4
3
2
1
0
0
STX02h
1
Command code (
‘
X
’
)
2
Disc number (100 digits)
3
Disc number (10 digits)
4
Disc number (1 digits)
5
Track number (10 digits)
6
Track number (10digits)
7
Next disc number (100 digits)
8
Next disc number (10 digits)
9
Next disc number (1 digits)
10
Next track number (10 digits)
11
Next track number (1 digits)
12
ETX03h
13
BCCH (high-level)
14
BCCL (low-level)
(1)
Answers returned
bytebit
7
6
5
4
3
2
1
0
0
STX02h
1
Reply code (
‘
X
’
)
2
Answer code
3
ETX03h
4
BCCH (high-level)
5
BCCL (low-level)
(2)
Special condition
•
Specify a disk number and a track number that are present and available as the parameters.
The disc
number (byte 2 to byte 4) must not be equal to the next disc number (byte 2 to byte 9).
•
This command is enabled only when the system status is Disc Sense
Complete (3) and when the zone status is No Disc (A) or Stop (B).
•
In case the Cross Fade Disc Reserve command cannot be submitted as the
command submission conditions are not satisfied (in the Auto Pause status), this command can
starts cross fade reproduction.
(3) Other