Dewalt DWFP72155 Instruction Manual - Page 10

Tool Operation Check Fig.1, Loading the Tool Fig. 4 - how to load

Get Dewalt DWFP72155 PDF manuals and user guides View all Dewalt DWFP72155 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English 2. Depress the trigger. To operate the tool using the BUMP ACTUATION method: 1. Depress the trigger. 2. Push the contact trip against the work surface. As long as the trigger is depressed, the tool will fire a fastener every time the contact trip is depressed. This allows the user to drive multiple fasteners in sequence. WARNING: Do not keep trigger depressed when tool is not in use. Keep the contact trip lock-off engaged in the locked position when the tool is not in use. Tool Operation Check (Fig.1) WARNING: If the tool is dropped or you suspect tool damage perform tool operation check. WARNING: Remove all fasteners from tool before performing tool operation check. SEQUENTIAL TRIP ACTION A. Press the contact trip against the work surface, without touching the trigger. THE TOOL MUST NOT CYCLE. B. Hold the tool off the work surface and pull the trigger. THE TOOL MUST NOT CYCLE. C. Pull the trigger and press the contact trip against the work surface. THE TOOL MUST NOT CYCLE. D. With finger off the trigger, press the contact trip against the work surface. Pull the trigger. THE TOOL MUST CYCLE. THE TOOL MUST NOT CYCLE. B. Hold the tool off the work surface, and pull the trigger. THE TOOL MUST NOT CYCLE. C. With the tool off the work surface, pull the trigger. Press the contact trip against the work surface. THE TOOL MUST CYCLE. D. Without touching the trigger, press the contact trip against the work surface, then pull the trigger. THE TOOL MUST CYCLE. Loading the Tool (Fig. 4) WARNING: Keep tool pointed in a safe direction when loading nails. WARNING: Never load nails with the contact trip or trigger activated. LOAD AND PULL PUSHER (FIG. 4) 1. Load nails through the slot in the rear of the magazine to past retaining clip. 2. Pull pusher back behind nail stick and release. 3. Ensure magazine pusher is behind the last nail stick. 4. Blow the magazine clean periodically to keep the pusher moving smoothly and to keep dirt and debris out of the nail channel. FIG. 4 CONTACT TRIP ACTION A. With finger off the trigger, press the contact trip against the work surface. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
2. Depress the trigger.
To operate the tool using the BUMP ACTUATION method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long as the
trigger is depressed, the tool will fire a fastener every time the
contact trip is depressed. This allows the user to drive multiple
fasteners in sequence.
WARNING:
Do not keep trigger depressed when tool is not in use.
Keep the contact trip lock-off engaged in the locked position when
the tool is not in use.
Tool Operation Check (Fig.1)
WARNING:
If the tool is dropped or you suspect tool damage
perform tool operation check.
WARNING:
Remove all fasteners from tool before performing tool
operation check.
SEQUENTIAL TRIP ACTION
A. Press the contact trip against the work surface, without touching
the trigger.
THE TOOL MUST NOT CYCLE.
B. Hold the tool off the work surface and pull the trigger.
THE TOOL MUST NOT CYCLE.
C. Pull the trigger and press the contact trip against the work
surface.
THE TOOL MUST NOT CYCLE.
D. With finger off the trigger, press the contact trip against the work
surface. Pull the trigger.
THE TOOL MUST CYCLE.
CONTACT TRIP ACTION
A. With finger off the trigger, press the contact trip against the work
surface.
THE TOOL MUST NOT CYCLE.
B. Hold the tool off the work surface, and pull the trigger.
THE TOOL MUST NOT CYCLE.
C. With the tool off the work surface, pull the trigger. Press the
contact trip against the work surface.
THE TOOL MUST CYCLE.
D. Without touching the trigger, press the contact trip against the
work surface, then pull the trigger.
THE TOOL MUST CYCLE.
Loading the Tool (Fig. 4)
WARNING:
Keep tool pointed in a safe direction when loading
nails.
WARNING:
Never load nails with the contact trip or trigger
activated.
LOAD AND PULL PUSHER (FIG. 4)
1. Load nails through the slot in the rear of the magazine to past
retaining clip.
2. Pull pusher back behind nail stick and release.
3. Ensure magazine pusher is behind the last nail stick.
4. Blow the magazine clean periodically to keep the pusher moving
smoothly and to keep dirt and debris out of the nail channel.
FIG. 4
English
8