Dyson DC25 Animal User Guide - Page 6

SAVE THESE INSTRUCTIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY Assembly Lie machine flat and attach cleaner head by sliding it on until it clicks. Stand vacuum cleaner up straight, attach wand to hose and push into place until it clicks. Push wand down into hose and attach tools to the side of the machine. Using your Dyson Press foot pedal and recline handle to use. The stabilizer stand will automatically lift up. To switch 'ON', depress power button in front of handle. When finished cleaning, push machine into an upright position and stabilizer wheels will automatically drop. Use the cyclone carry handle to carry the machine. Caution: (i) If the vacuum cleaner is not functioning properly, has been dropped, damaged, left outdoors, or immersed in liquid, contact the Dyson helpline. (ii) Do not allow the vacuum cleaner to be used by anyone who may not be able to operate it safely. (iii) The use of an extension cord is not recommended. (iv) Always switch off and unplug before performing maintenance on your appliance. (v) When returning to the upright position, ensure that the stabilizer wheels are fully engaged before releasing the cleaner. (vi) Ensure the cyclone is secured to the machine. Do not press the cyclone release button or shake the appliance while carrying or it could fall and cause injury. (vii) Store the machine indoors. Put the vacuum cleaner away after use with the cable coiled safely, to prevent tripping hazards. (viii) Do not use your vacuum cleaner outdoors or on wet surfaces. Vacuum may be used inside a garage only when used with the Model 08909 Dyson Car Cleaning Kit accessories. If used in a garage, care should be taken to wipe the soleplate and wheels with a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could damage delicate floors. (ix) Do not use outdoors or on wet surfaces or to vacuum water or other liquids - electric shock could occur. (x) Check to ensure your electricity supply corresponds to that shown on the rating plate, which can be found behind the clear bin.TM The machine must only be used as rated. (xi) Do not lubricate any parts, or carry out any maintenance or repair work other than that shown in this manual, or advised by the Dyson Helpline. Please note: • This machine is intended for domestic use only. Fine dust such as plaster dust or flour should only be vacuumed in very small amounts. • Do not use the machine to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the machine. • When vacuuming, certain carpets may generate small static charges in the clear binTM or wand. These are entirely harmless and are not associated with the electricity supply. To minimize any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied it and rinsed it out with cold water. • C onsult your flooring manufacturer's recommended instructions before vacuuming and caring for your flooring, rugs, and carpet. Some carpets will fuzz if a rotating brushbar is used when vacuuming. If this happens, we recommend vacuuming in bare floors mode and consulting with your flooring manufacturer. Hard floors or carpets The brushbar will always default to 'ON' (spinning) each time you switch on the machine and recline it for cleaning. The brushbar will automatically stop if it becomes obstructed. If the brushbar stops during use, please refer to the 'Clearing brushbar obstructions' section. To switch the brushbar off (e.g. for hard floors), recline the machine and turn it 'ON', then press the brushbar 'ON/OFF' button - the brushbar will stop spinning. Using the tools - High-reach cleaning Caution: (i) Switch 'OFF' machine before changing tools. (ii) Powerful suction can cause the hose to 'pull back' - please take care. (iii) Take extra care when vacuuming on stairs; do not work with the vacuum cleaner above you on the stairs. Do not put the vacuum cleaner on chairs, tables etc. (iv) Ensure machine is in upright position before using tools. To release the wand, open the wand cap and pull the red tube until the wand releases from the vacuum. Tools can be attached to either the hose or wand. The brushbar will not rotate when the machine is in an upright position. Ensure wand cap is closed when not in use. Emptying the Clear binTM Caution: (i) Switch 'OFF' machine and unplug before emptying the bin. Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. To remove the clear binTM from the machine press the button at rear of cyclone carrying handle. To release the dirt, press the red bin release button. Please note: (i) Do not use the machine without the clear binTM in place. Cleaning the Clear binTM Caution: (i) Do not immerse the whole cyclone in water or pour water into the cyclones. (ii) Ensure bin is completely dry before replacing. Please note: (i) Do not use detergents, polishes or air fresheners to clean the bin. (ii) Do not put bin in a dishwasher. Washing your filters Caution: (i) Switch 'OFF' and unplug machine before removing the filters. (ii) Ensure filters are completely dry before refitting to machine. This machine has two filters, located as shown. It is important to check your filters regularly and wash at least every 3 months according to instructions, to maintain performance. The filter in the ball should be rinsed and tapped out until the water runs clean, then tapped out again to ensure all excess water is removed. This will normally require up to 10 rinse cycles. Please leave to dry completely for 24 hours. Please note: (i) It is normal for this filter in the ball to turn grey in color. The filters may require more frequent washing if vacuuming fine dust. (ii) Do not use detergents to clean the filters. (iii) Do not put the filters in the dishwasher, washing machine, tumble dryer, oven, microwave or near an open flame. Looking for blockages Caution: (i) Switch 'OFF' and unplug machine before checking for blockages. Failure to do so could result in personal injury. (ii) Please ensure machine is upright and switched off before removing hose or airway inspection parts. (iii) Beware of sharp objects when clearing blockages. (iv) Refit all parts of the machine securely before using. Please note: (i) Clearing blockages is not covered by your machine's limited warranty. This machine is fitted with a thermal cut-out. If any part of your machine becomes blocked, it may overheat and then automatically shut off. Switch 'OFF' and unplug machine and leave to cool down for at least 60 minutes before attempting to check filters or for blockages. Clear blockage before restarting. SAVE THESE INSTRUCTIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY