Edimax BR-6478Gn Manual - Page 45

AP Bridge-WDS

Get Edimax BR-6478Gn PDF manuals and user guides View all Edimax BR-6478Gn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

to connect to this router. 2.4GHz (N): Allows 802.11n wireless network clients to connect to this router. 2.4GHz (B+G): Allows 802.11b and 802.11g wireless network clients to connect to this router. 2.4GHz (G): Allows 802.11g wireless network clients to connect to this router. Channel Number MAC Address 1 to 4 Wireless Module 2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). Select a channel from the dropdown menu. All access points must use the same channel (1 to 13). Input the MAC addresses of the wireless access points with which you wish to connect. Select "Enable" to turn on the 2.4GHz wireless signal and select "Disable" to turn it off. Click "Apply" to save the changes, or click "Cancel" to discard the changes. After you have clicked "Apply", you will see the following message: Click "Apply" to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click "Continue" to configure other settings. 3‐4‐1‐5 AP Bridge-WDS In "AP Bridge-WDS" mode, this broadband router acts as both a wireless communication bridge and a wireless access point. This router can connect to up to 4 WDS‐compatible wireless access points and allows the computers connected every AP to communicate with each other. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
44
to connect to this router.
2.4GHz (N): Allows 802.11n wireless network clients
to connect to this router.
2.4GHz (B+G): Allows 802.11b and 802.11g wireless
network clients to connect to this router.
2.4GHz (G): Allows 802.11g wireless network clients
to connect to this router.
2.4GHz (B+G+N): Allows 802.11b, 802.11g, and
802.11n wireless clients to connect to this router
(recommended).
Channel Number
Select a channel from the dropdown menu. All access
points must use the same channel (1 to 13).
MAC Address 1 to 4
Input the MAC addresses of the wireless access points
with which you wish to connect.
Wireless Module
Select “Enable” to turn on the 2.4GHz wireless
signal and select “Disable” to turn it off.
Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have
clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60
seconds for the broadband router to restart. Click “Continue” to configure other settings.
3
‐
4
‐
1
‐
5 AP Bridge—WDS
In “AP Bridge—WDS” mode, this broadband router acts as both a wireless communication
bridge and a wireless access point. This router can connect to up to 4 WDS
‐
compatible
wireless access points and allows the computers connected every AP to communicate with
each other.