Electrolux EFLS527UTT Wiring Diagram English - Page 6

6 Troubleshooting Tests Washer Troubleshooting Tests, continued Test 9 Test 10 Test 11 Test 12 Test 13 Test 14 Test 15 Test 16 Test 17 Test 18 Test 19 Test 20 Test 21 Test 22 Test 23 1. Remove the belt from the motor and spin the motor pulley. Does the motor spin free? No, replace the motor. Yes, go to step (2). 2. Spin the tub pulley. Does the tub spin free? No, check the tub bearings. Yes, go to step (3). 3. Disconnect the plug from the drive motor and measure the resistance If the meter reads other than between 105 to 130 Ohms, replace the motor. If between pins 4 & 5 in the motor. the reading is between 105 to 130 Ohms, go to step (4). 4. Disconnect the plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings must be between 3 and 6 Ohms. If the readings are correct, replace the motor control board. If the readings are incorrect, replace the motor. Communication problem. Check the wiring between the main control board and the motor control board. If wiring is bad, correct wiring problem. If wiring is good, replace the main control board. If the problem is not corrected, replace the motor control board. Communication problem. Check the wiring between the main control board and the user interface board. If wiring is bad, correct wiring problem. If wiring is good, replace the user interface board. If the problem is not corrected, replace the main control board. Have the power company or professional check the frequency and voltage of the incoming power under load. If correct, for error code E5C, replace the motor control board. If correct, for error codes H1/B1, H2/B2, H3/B3, HE/BE, or H5/B5 replace the main control board Check the resistance of the water NTC. Is it around 4.8K ohms? No, replace the NTC sensor Yes, check the wiring. 1. Check the resistance of the heating element. It should be approximate- If the reading is incorrect, replace the heating element. ly 14 ohms. If the reading is correct, move to the next step. 2. Check the resistance between ground and both heater terminals. It should be open when the heater terminals are disconnected. If the readings are incorrect, replace the heating element. If the problem is not corrected, check the wiring, If wiring is OK, replace the main control board. Check wiring between the main control board and motor control board. If wiring is good, replace the motor control board. 1. Are the hot and cold water hoses switched? Yes, switch the hoses to correct position No, go to step 2 2. Is the HOT water about the same temperature as the cold? Yes, fix the HOT water in the house supply. 1. Check wiring between main board and pump. If OK, then go to step (2). 2. Check wiring between main control and recirculation board. If OK, then go to step (3). 3. Check pump for open coil (resistance check). If OK, then replace main control. 1. Check power in for voltage under load. Correct supply or branch circuit issues. No problem go to step 2. 2. Check power wiring to main board. Yes, fix wiring or plug to main board. No, go to step 3. 3. Check wiring to motor board for short to power or ground. Yes, fix problem. No, replace the main board. Check wiring to main board. Unplug the unit for 1 minute and retry. If problem is not corrected replace main control. Unplug and re-seat connector between UI boards. If problem persists, replace UI satellite board. Check wiring to recirculation pump If wiring is bad, correct wiring problem. If wiring is good, replace recirculation pump. If the problem is not corrected, replace the main control board. Check wiring to concentrated wash pump If wiring is bad, correct wiring problem. If wiring is good, replace concentrated wash pump. If the problem is not corrected, replace the main control board. 1. Is the incoming hot water supply on? Yes, go to step (2). No, turn ON incoming hot water supply at wall. 2. Does there appear to be an issue with the wiring harness from main board to flow meter? No, replace main board and go to step (3). Yes, Perform continuity testing on J12 connector from main board and Flow Meter harness: Pin-6 to Pin-3, Pin-7 to Pin-2, Pin-8 to Pin-1. If issues continue, replace main board and continue to step (3). 3. Is the issue is still present? Test 24 1. Does water enter the washer continuously? 2. Remove power from washer. Does the water stop coming in? 3. Replace the valve assembly. Did this correct the problem? Yes, replace flow meter/valve housing. Yes, got to step (2). No, check air trap for clog, if not, replace the main control board. No, replace water valve assembly. Yes, Check wiring to valve assembly for shorts. If wiring is good, replace the main control board. Yes, problem solved.