Electrolux EI24ID30QS Installation Instructions (English) - Page 2
Caution, Warning
View all Electrolux EI24ID30QS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
5. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. 6. Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16" (0,8 cm) below underside of countertop to top of console. 7. Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 7a. 8. Adjust levelers up or down until dishwasher is level. See Figure 7b. Figure 7a II I Figure 7b Figure 8 D Finishing the Water and 7 Electrical Connection A CAUTION Property Damage Do not solder within 6" (15,24 cm) of the water inlet valve. Damage to the plastic parts in the valve may occur. Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. Water Line 1. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supplyatshut-off valve. 2. Route water line to water inlet valve as shown in Figure 4. 3. While firmly pulling water supply line into 90° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. 4. Turn on water supply and check for leaks. Electrical Supply 1. Remove junction box cover and pull house wiring into junction box. See Figure 9 2. Use a UL listed conduit connector (not included) at box to stabilize wiring. 3. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight. Figure 9 A WARNING Electric Shock Hazard Grounding Instructions: The dishwasher must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. Do not connect the dishwasher to the power supply until the appliance is permanently grounded. All wiring connections must be enclosed in the junction box. This unit has copper lead wires. Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Failure to follow these instructions could result in death or serious injury. 9 C3 Option "A" 9. Holes need to be pre-drilleld using a 05 drill to secure unit 10. Screw mounting brackets firmly to cabinet using screws provided in installation packet. See Figure 8 11. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly, adjust rear foot if small correction is needed until door opens and closes freely. Adjust the levelling legs. Installation Diagram 6 Green Wire to Green Wire (Ground) Black Wire to Black Wire (Hot) White Wire to White Wire (Neutral) 4. Replace junction box cover.See Figure 10 Figure 10 IN1 Option "B" Green Wire 0 to Green Wire (Ground) Black Wire to Black Wire (Hot) 9 White Wire to White Wire (Neutral) Finishing the Drain 8 Connection 1. Review Figures 12, 13 and 14 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. 14ir ¶ap cD AA c Right Side Installation Figure B 3. If you connect to a sink trap,local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 13 An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). 4. If you connect to a disposer, the large end of drain hose will fit. Figure 14 (a) The knock outplugmust be removed from inside disposer inlet before making the final fit to drain hose. See Figure 14 (b). 34/ a 1.0" 1,9 Cm.) (2,5cm.) Larger end of hose fits disposer inlet fitting Figure 14(a) Cutfor %"(1,6 cm) connection. Sink at Left Drain Air Gap 1\ 11 II lternate rain Through Floor into Separate Trap Remove" Knockout Plug in Disposer Figure 14(b) Sink at Right 2" (5,08 cm) Drain Hose Hole The drain hose loop must be at least 32"(80 cm) highfrom thefloor to insure proper drainage. KICKPLATE ASSEMBLY Figure 11 Water Line eveling Leg frN Electrical Line u check these items: Water and electrical lines are straight out in front of the dishwasher. All three leg levelers are positioned properly. Cabinet Seals are positioned on the sides of the dishwasher. u Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. > 0 ill Entry Must be Above Trap Branch Tailpiece rl Sink at Left Figure 12 Sink at Right 2" Drain Hose Hole The drain hose loop must be at least 32" (80 cm) high from thefloor to insure proper drainage. 5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. 6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. 7. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. 8. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. 2. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 12. A WARNING Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury A CAUTION Cut Hazard Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to follow this warning may result in injury. A CAUTION Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. Failure to follow this warning could result in electric shock. Water and drain lines have no kinks and move freely behind the dishwasher. Water supply is turned on. Joints are free of leaks. Wiring connections to junction box are tight all access panels are secured back in place. Replace kickplate. See Figure 11 Drain hose is connected properly to outlet. All packing materials and consumer literature have been removed from inside unit. Dishwasher is level and securely fastened. Open and close door to make sure it does not hit surrounding cabinet or countertop. Make re that all wire ties are removed from the rack assembly Checking the Installation 9 Operate the machine through at least one fillandpump-out, checking the following items: U At first fill, approximately 4 minutes make sure water completely covers filter surface. U At pump-out: (pump-out is either when the cycle is completed or canceled. refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. U Check water connections again for leaks.