Electrolux EI24ID50QS Product Specifications Sheet (English) - Page 3
Front, Right - canada
View all Electrolux EI24ID50QS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
EI24ID80Q / EI24ID50Q / EI24ID30Q DISHWASHER EI24ID50QS Front 23 3/4" Left 24 1/4" Right 50 1/4" 22 1/2" 33 3/4" Adjustable to 35 3/4"* Door in 90° open position 27 3/4" FPO *Height only adjustable to 353/4" max. when installed in 353/4" max. standard cabinetry cutout. (Dimensions do NOT include insulation - insulation blanket may be compressed during installation.) 90° 90° Electrical, water, Power supply & water inlet location (bottom rear) 34" min. to 35 3/4" and drain lines must be confined to shaded area max.** Preferred drain areas 24" min. 3" 18" 3" 3" 3 1/2" min.to 4 1/2" max. **NOTE: 35 3/4" max. height for standard cabinetry cutout. 11/4" (5/16" min. clearance required from unit to 1" 21/4" underside of countertop.) 21/4" 24" Built-In Dishwasher Specifications • Product Weight - 98 Lbs. • Voltage Rating - 120V/60Hz/15 Amps • Connected Load (kW Rating) @120 Volts = 1.44 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120V = 15A • Always consult local and national electric & plumbing codes. Meets requirements of ASSE 1006 - integral air gap on supply. • Water Pressure - Hot water line to dishwasher must provide between 20 and 90 pounds per square inch (psi) with at least 120° F hot water temperature. • Make sure location has correct drain, water and electrical outlets to make connections. • Electrical and water supplies should enter cabinet opening on floor, or through back or side walls, as shown in shaded areas. • Keep back free of drain, water & electrical supply. • Connections preferably located toward left side of dishwasher. Do not cross drain, water or electrical lines in front of motor, blower or frame. • If connecting drain hose to sink trap, local code may require installation of Air Gap Kit (not included). • Leveling legs supplied to adjust height. (Note: Height only adjustable to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout. 5/16" min. clearance required from top of unit to underside of countertop. Dimensions do NOT include insulation - insulation blanket may be compressed during installation.) • When installing adjacent to wall, cabinet or other obstruction that extends beyond front edge of unit, allow 2" minimum clearance between opened door and obstruction. • Floor should be flat and free of obstructions. • When installing at end of cabinet line, sides and back must be fully enclosed. • Do not install unit under a cooktop, damage will occur. • Recommended to seal cabinets, enclosing all sides of dishwasher, including underside of countertop, with oil-based paint or moisture-proof polyurethane to prevent possible steam/moisture damage. Note: F or planning purposes only. Refer to Product Installation Guide on the web at electroluxappliances.com for detailed instructions. Electrolux Major Appliances, N.A. USA • 10200 David Taylor Drive • Charlotte, NC 28262• 1-877-4electrolux (1-877-435-3287) • electroluxappliances.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxappliances.ca EI24ID50Q 04/14 © 2014 Electrolux Home Products, Inc. Meets requirements of ASSE 1006 High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice.