Electrolux EIFLS60LSS Operating Instructions (Operating Instructions)

Electrolux EIFLS60LSS Manual

Electrolux EIFLS60LSS manual content summary:

  • 1
  • 2

IMPORTANT
Please read all safety instructions before using your
new front-loading washer. For best washing results
with your new washer, remember to review:
9
INSTALLATION INSTRUCTIONS
9
USE & CARE GUIDE
NOTE TO
INSTALLER
Leave these instructions
with the customer.
IMPORTANT
This washer requires periodic cleaning
maintenance. Refer to cleaning instruc-
tions included with the unit literature.
CAUTION
EXCESSIVE WEIGHT HAZARD
Avoid back or other injury. Use more than one
person to move, tip or lift the washer.
ELECTRICAL SHOCK HAZARD
Washer must be properly grounded at all times.
REMARQUE POUR
L’INSTALLATEUR
Laissez ces instructions au
client.
Suite de la version française au verso.
NOTA AL
INSTALADOR
Deje estas instrucciones
con en cliente.
Español continua en la pagina trasera.
137269700A (0911)
For toll-free telephone support in the U.S. and Canada:
1-877-4ELECTROLUX (1-877-435-3287).
For online support and product information,
Para obtener asistencia telefónica gratuita en los Estados Unidos y Canadá:
1-877-4ELECTROLUX (1-877-435-3287).
Para obtener asistencia e información en Internet sobre el producto,
Pour rejoindre le service sans frais aux États-Unis et au Canada:
1-877-4ELECTROLUX (1-877-435-3287).
Pour obtenir de l’aide et de l’information sur les produits en ligne,
USE ONLY LOW-SUDSING, HIGH
EFFICIENCY DETERGENT.
UTILISEZ UN DÉTERGENT
HAUTE EFFICACITÉ QUI
PRODUIT PEU DE MOUSSE.
UTILICE UN DETERGENTE PARA
ROPA QUE PRODUZCA POCA
ESPUMA Y QUE SEA DE ALTA
EFICIENCIA.
ADJUST
LEVEL BOTH WAYS
CHECK STABILITY,
CORNER-TO-CORNER
raise
lower
A)
B)
C)
LEVEL
B)
C)
D)
E)
F)
G)
H)
A)
DETERMINE
HOT SUPPLY
TURN ON WATER,
CHECK FOR LEAKS
WRAP DRAIN HOSE,
SNAP IN PLACE
SECURE DRAIN HOSE WITH
SUPPLIED CABLE TIE
CONNECT TO GROUNDED
OUTLET, DO NOT REMOVE
GROUNDING PRONG
TIGHTEN ADDITIONAL
2/3 TURN WITH PLIERS
INSTALL HOT HOSE ON HOT
SUPPLY, COLD HOSE ON
COLD SUPPLY (HAND-TIGHT)
INSPECT FOR RUBBER
WASHERS
24” min
(60cm min)
CONNECT
Perform brief installation cycle for your model as follows:
Empty washer drum and close door.
1.
Wake washer up (any button), rotate cycle knob to
2.
hand wash
, press
start
then
cancel
.
Wake washer up again, immediately and simultaneously press and hold
3.
eco friendly
and
my favorite
buttons for
5 seconds
.
LCD will display
4.
INSTAL CYCLE
and show estimated time of cycle completion.
Press
start
.
Installation Cycle will perform various diagnostic routines.
5.
At cycle completion, LCD will display
6.
INSTAL PASS!
or prompt an action dur-
ing cycle such as
CHECK HOSES
,
NO WATER
or
CALL SERVICE 877 435
3287
.
Washer will exit the Installation Cycle and return to normal operation next time you
7.
wake it up. Read Use and Care Guide and enjoy your new premium washer!
Empty washer drum and close door.
1.
Wake up the washer by pressing any button and then follow the prompts on the
2.
LCD User Interface, including language selection.
NOTE
: this initial, automatic cycle
can be manually accessed through the scroll buttons in the
set prefs
sections
under
options
.
LCD will display
3.
INSTAL CYCLE
and show estimated time of cycle completion.
Press
start
.
Installation Cycle will perform various diagnostic routines.
4.
At cycle completion, LCD will display
5.
INSTAL PASS!
or prompt an action during
cycle such as
CHECK HOSES
,
NO WATER
or
CALL SERVICE 877 435 3287
.
Washer will exit the Installation Cycle and return to normal operation next time you wake it
6.
up. Read Use and Care Guide and enjoy your new premium washer!
If washer has
this console:
If washer has
this console:
P
f
bi
OPERATE
RETURN UPRIGHT
EMPTY DRUM
CONTENTS
CAREFULLY
TIP
REMOVE & SAVE
PROTECT
FLOOR
A)
B)
C)
D)
CART FROM
REAR ONLY
DO NOT CART
FROM FRONT
DO NOT USE OPEN
DISPENSER DRAWER AS
HAND-HOLD LOCATION
DO NOT CART
FROM SIDE
DO NOT USE OPEN
DOOR TO LIFT OR
TIP THE UNIT
DO NOT USE KNEE
IN CABINET SIDE
TO MOVE UNIT
2-PERSON CARRYING
STRAPS, FRONT-TO-
BACK RECOMMENDED
UNPACKING & HANDLING
RETURN UPRIGHT
x 7
x 5
x 1
x 5
x 5
A)
B)
REMOVE
INSERT
NOTE
Rubber material in shipping bolt spacer may
need some time to relax before it can be pulled
through holes in back panel.
IMPORTANT
Retain all shipping materials, including bolts, spacers,
foam base and foam plug. Reinstall to help prevent
damage to washer during any future moves.
REMOVE & INSERT
HOLE PLUGS (IN BAG)