Electrolux EW30EC55GB Dimensions - Page 4

Cooktop/Downdraft Vent Countertop Preparation Countertop Preparation for 30" & 36" Cooktop / Downdraft Vent Installation For detailed cooktop and downdraft vent installation specifications, refer to model-specific product page and installation guide on web Top Vertical noncombustible surface - rear wall B Backsplash 3/4" max. 23 1/4" min. C 25" Flush with back side of cabinet front A E30DD75ESS / 30" Cooktop Cutout Dimensions 30" Cooktops EW30IC60I EW30CC55G EW30EC55G EW30GC55G EW30GC60I A 30" 30" 30" 28 1/2" 28 1/2" B 27 3/4" 27 3/4" 27 3/4" 27 3/4" 27 3/4" C 20 1/2" 20 1/2" 20 5/8" 19 3/4" 19 3/4" D 23 5/16" 23 5/16" 23 7/16" 22 9/16" 22 9/16" E 24 5/16" 24 5/16" 24 7/16" 23 9/16" 23 9/16" Countertop backsplash Studwall 25"(standard countertop)* 3/4" max. backsplash thickness 1/4" min. flat ledge 213/16" 2 1/8" Downdraft chimney top Countertop raised lip 3" 1 15/16" Stiffener 9/32" Cooktop 213/16" Vent unit Back side of cabinet front Vertical noncombustible surface - rear wall 23 1/4" min. D* E** 1/4" min. flat ledge 2 9/16" * Overall flat ledge behind backside of cabinet front ** Minimum flat surface required to fit top surface of cooktop and downdraft vent cap E36DD75ESS / 36" Cooktop Cutout Dimensions 36" Cooktops EW36IC60I EW36CC55G EW36EC55G EW36GC55G A 36 1/4" 36 1/4" 36" 34 1/4" B 33 3/4" 33 3/4" 33 3/4" 33 3/4" C 20 1/2" 20 1/2" 20 5/8" 19 3/4" D 23 5/16" 23 5/16" 23 7/16" 22 9/16" E 24 5/16" 24 5/16" 24 7/16" 23 9/16" Cooktop Installation Note: To ensure proper installation, refer to model-specific installation guide on web for cooktop dimensions, cutout dimensions and cabinet requirements. Due to varying cooktop depths, tight fit is possible between cooktop and vent. Countertop Preparation Note: Be aware of areas of potential interference called out in illustration. Countertop with raised lip and/or backsplash may not allow enough flat area for proper installation, 2-13/16" of flat countertop required behind cooktop. No gap required between back of cooktop and front of downdraft trim piece. *Standard 25" countertop depth may NOT be adequate for some cooktop/vent installations, especially with backsplash. Cooktop / Downdraft Vent Countertop Preparation Specifications • For detailed Cooktop installation, refer to model-specific product page and installation guide on web. Plan installation so that all required minimum clearances between cooktop, overhead cabinets and adjacent vertical walls are provided. • Position cooktop / vent cutout so all required minimum clearances are met. • Minimum flat countertop area must meet or exceed combined overall width and depth as shown. Standard 25" countertop depth may NOT be adequate for some cooktop / vent installations, especially with backsplash. • Separate circuits required for cooktop and vent. (Refer to product-specific electrical specifications.) • Always consult local and national electric and gas codes. Check local building codes for installation requirements, as they may vary per locale. Downdraft Vent Specifications • For detailed Downdraft Vent installations, refer to model-specific product page and installation guide on web. • Voltage Rating - 120V / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 1.0 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120 Volts = 8.0 Amps • Vent unit outside of building only. • Vent must be installed in vertical orientation only. • 1,600 CFM remote exhaust blower (PN # 5304444802) included with vent - shipped in separate box. • Do not use flexible duct. Round duct instead of rectangular duct recommended, especially when elbows are required. • When multiple elbows are necessary, ensure a minimum of 24" of straight duct between any two elbows. • Thermal breaks such as short section of nonmetallic duct, should be used in areas of extreme cold. • For most efficient airflow exhaust, use a straight run or as few elbows as possible. • Cold weather installations should have additional backdraft damper installed. • Installing a Downdraft Vent in combination with any gas cooking surface will affect optimum burner efficiency. Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxappliances.com for detailed instructions. Electrolux Major Appliances, N.A. USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-877-4electrolux (1-877-435-3287) • electroluxappliances.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxappliances.ca DIC_DDV_PREP EL 10/10 © 2010 Electrolux Home Products, Inc. High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice. Printed in the U.S.A.