Epson PowerLite Pro G5750WU Operation Guide - EasyMP Monitor v4.51 - Page 30

Monitoring window layout

30

*1

When Temperature level display group view is set to On at Environment

setup in the Tool menu, an icon indicating the internal temperature of the

projector will be displayed on top of the projector icon. The default setting

is Off.

*2

Check the following items.

- Check that the projector's power is turned on.

- Check that the LAN cable is connected.

- Check that Standby Mode is set to Communication On (or Network On)

or Network Monitoring is set to On in the projector's configuration menu.

*3

Check that the projector has been correctly connected to the network.

*4

It describes DVI-D if the projector is equipped with both DVI-D and HDMI

input terminal.

*5

It describes HDMI if the projector is equipped with both DVI-D and HDMI

input terminal.

*6

Using Environment setup in the Tool menu, you can set a duration of time

after which the Replace Lamp notification will appear. (The notification will

appear earlier if the lamp needs to be replaced before the selected time.)

q

Detectable error information differs with the projector you are using.

Checking properties in detail

You can check the properties of Group and projectors in detail.

Lamp error (Lamp 2)

Lamp failure at power on

(Lamp 1)


(Lamp 2)

High-temperature warning

Replace Air Filter

No Air Filter

Low Air Flow

Air Flow Sensor Err.

Supply System Error (Ballast

1)


2)

Cinema filter warning

Shutter warning

Lamp Cover Open

Lamp Error

Lamp Error (Lamp 1)

Lamp Error (Lamp 2)



(Lamp 1)


(Lamp 2)

High internal temperature

error

Low air flow error

Air filter air flow sensor error

Internal Error

Fan error

Sensor error

Supply System Error

(Ballast)


1)


2)

Auto Iris Error

Cinema filter error

Shutter error

Cooling system error

(Peltier element)

Cooling system error

(pump)

Other error

Exhaust vent shutter error

Other warning

Section	Page
Front	1
Notations Used in This Guide	2
Contents	3
EasyMP Monitor Features	5
Tasks that can be done using EasyMP Monitor	6
Installing EasyMP Monitor	7
Operating environment	7
Transferring the settings	7
Installing	8
Limitations imposed by a Windows Vista or Windows 7 environment	8
Before starting operations	8
Using EasyMP Monitor	9
Registering and deleting projectors for monitoring	10
Starting EasyMP Monitor	10
Registering projectors using automatic search (Searching for and registering projectors that are located in the same segment)	11
Setting the range of addresses to do an automatic search and registration	13
Registration by specifying an IP address (Manual registration)	16
Registering several projectors to a monitoring group all at once	17
If the projector name or IP address changes after registration	19
Cancelling projector registrations (Delete)	19
Monitoring window layout	20
Types of monitoring windows and switching method	20
Monitoring using Grouping view	21
Monitoring using Detail list view	23
Searching for desired icons (Projector list)	26
Monitoring using the system tray	26
Displaying projectors with problem or warning statuses in a list	27
Checking properties in detail	30
Displaying and deleting logs	31
Using the control functions	33
Carrying out control using control buttons	33
Carrying out control using a web browser (Web control)	35
Carrying out control using timer settings	35
Mail notification function settings	38
An e-mail notifying the operator of a problem/warning/status is issued	40
Application lock function	43
Switching Application lock between enabled and disabled	43
Setting a password for cancelling application lock	43
Appendix	44
Troubleshooting	45
Projectors cannot be monitored or controlled	45
An e-mail message is not sent when a problem occurs with a projector	45
Uninstalling EasyMP Monitor	46
General Notice	47

Epson PowerLite Pro G5750WU Operation Guide - EasyMP Monitor v4.51 - Page 30

Checking properties in detail, Check that Standby Mode is set to Communication On or Network

Page 30 highlights