Epson S6 User Manual - Page 53

Status, Cause, Remedy or Status, Lamp Cover Open

Get Epson S6 PDF manuals and user guides View all Epson S6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Problem Solving 53 Status Red Red Cause Lamp Error Lamp Failure Lamp Cover Open : Lit : Flashing: : Off Remedy or Status Check the following two points. • Take out the lamp and check if it is cracked. s p.68 • Clean the air filter. s p.65 If it is not cracked - Re-fit the lamp and turn on the power. If the error continues - Replace the lamp with a new lamp and turn on the power. If the error continues - Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. s Epson Projector Contact List If it is cracked - Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). s Epson Projector Contact List Check that the lamp cover and the lamp are securely installed. s p.68 If the lamp cover or the lamp is not securely installed, the lamp does not switch on. When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Problem Solving
53
Lamp Error
Lamp Failure
Lamp Cover Open
Check the following two points.
•
Take out the lamp and check if it is cracked.
s
p.68
•
Clean the air filter.
s
p.65
If it is not cracked - Re-fit the lamp and turn on the power.
If the error continues - Replace the lamp with a new lamp and turn on the power.
If the error continues - Stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the
Support and Service Guide
.
s
Epson Projector Contact List
If it is cracked - Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself,
be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced).
s
Epson Projector Contact List
Check that the lamp cover and the lamp are securely installed.
s
p.68
If the lamp cover or the lamp is not securely installed, the lamp does not switch on.
When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On".
s
p.45
: Lit
: Flashing:
: Off
Status
Cause
Remedy or Status
Red
Red