Fisher and Paykel DD60DCX6 User Guide - Page 35

Possible Cause

Get Fisher and Paykel DD60DCX6 PDF manuals and user guides View all Fisher and Paykel DD60DCX6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Troubleshooting 33 Problem Possible Cause What to do Continuous beeping A fault has occurred. Refer to the 'Fault codes' section. Intermittent beeping DishDrawer® is in pause mode. Close the DishDrawer® and press the button. DishDrawer® will not start Power supply is not connected. Connect the power supply. The drawer is not closed properly. Keylock or Childlock feature is on. Ensure the drawer is firmly closed. Turn the Keylock or Childlock off. Hold down the / button until the symbol disappears from the LCD screen or the light above the / button disappears. Water under the drain filter button not pressed. Press the This is normal and needs no action. button. Excess water in the Drain hose(s) bent or DishDrawer® kinked. Straighten the drain hose(s). Blocked filters. Clean the filter plate/drain filter. Refer to the 'User maintenance instructions' section. Water marks on the Rinse aid depleted. dishes Rinse aid setting too low. Refill the rinse aid dispenser. Increase the rinse aid setting. DishDrawer® overloaded/ incorrectly loaded. Refer to the section on loading. DishDrawer® interior is stained Some foods, like tomato based products, may stain the inside of the DishDrawer®. Pre-rinse dishes before placing in the DishDrawer®. Alternatively, using the Rinse programme after adding the dishes may minimise staining. Dishes did not dry Incorrect loading. Ensure the dishes are not nesting together. Rinse aid depleted. Refill the rinse aid dispenser. Rinse aid setting too low. Increase the rinse aid setting. Eco wash programme used. Choose a standard wash programme. No detergent dispensed Detergent dispenser was wet when loaded. Clean the dispenser and ensure the dispenser is dry when adding detergent. Excessive motor noise The filter plate and/or spray Refer to the 'User maintenance instructions' arm is incorrectly placed. section for details on correct placement. No water in the motor area. This usually occurs on the first use or when the DishDrawer® has not been used for long periods of time. Run the DishDrawer® through a wash programme.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
33
Troubleshooting
Problem
Possible Cause
What to do
Continuous
beeping
A fault has occurred.
Refer to the ‘Fault codes’ section.
Intermittent
beeping
DishDrawer® is in pause
mode.
Close the DishDrawer® and press the
button.
DishDrawer® will
not start
Power supply is not
connected.
Connect the power supply.
The drawer is not closed
properly.
Ensure the drawer is firmly closed.
Keylock or Childlock feature
is on.
Turn the Keylock or Childlock off.
Hold
down the
/
button until the
symbol
disappears from the LCD screen or the light
above the
/
button disappears.
button not pressed.
Press the
button.
Water under the
drain filter
This is normal and needs no action.
Excess water in the
DishDrawer®
Drain hose(s) bent or
kinked.
Straighten the drain hose(s).
Blocked filters.
Clean the filter plate/drain filter.
Refer to the
‘User maintenance instructions’ section.
Water marks on the
dishes
Rinse aid depleted.
Refill the rinse aid dispenser.
Rinse aid setting too low.
Increase the rinse aid setting.
DishDrawer® overloaded/
incorrectly loaded.
Refer to the section on loading.
DishDrawer®
interior is stained
Some foods, like tomato
based products, may
stain the inside of the
DishDrawer®.
Pre-rinse dishes before placing in the
DishDrawer®. Alternatively, using the Rinse
programme after adding the dishes may
minimise staining.
Dishes did not dry
Incorrect loading.
Ensure the dishes are not nesting together.
Rinse aid depleted.
Refill the rinse aid dispenser.
Rinse aid setting too low.
Increase the rinse aid setting.
Eco wash programme used.
Choose a standard wash programme.
No detergent
dispensed
Detergent dispenser was
wet when loaded.
Clean the dispenser and ensure the
dispenser is dry when adding detergent.
Excessive motor
noise
The filter plate and/or spray
arm is incorrectly placed.
Refer to the ‘User maintenance instructions’
section for details on correct placement.
No water in the motor area.
This usually occurs on the first use or when
the DishDrawer® has not been used for
long periods of time.
Run the DishDrawer®
through a wash programme.