Frigidaire ATF8000FS Data Sheet

Frigidaire ATF8000FS - Gallery - Washer Manual

Get Frigidaire ATF8000FS - Gallery - Washer PDF manuals and user guides
UPC - 012505377525
View all Frigidaire ATF8000FS manuals
Add to My Manuals
Save this manual to your list of manuals

Frigidaire ATF8000FS manual content summary:

  • Frigidaire ATF8000FS | Data Sheet - Page 1
    and a letter or two letters. The control will beep and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash. Troubleshoot the problem by using charts on the pages 3-5. Quick Check If there is no error displayed and the washer momentarily starts then turns back off: 1. Listen
  • Frigidaire ATF8000FS | Data Sheet - Page 2
    Error code Error code chart Fault condition E11 Fill time too long. E13 Water leak in tub or air leak in air bell. E21 Water not pumping out fast enough. E23 Drain pump relay on control board failed or wire off pump. E24 Drain pump relay on control board failed or wire off pump. E31 Pressure
  • Frigidaire ATF8000FS | Data Sheet - Page 3
    the pressure switch. 4. Better models, replace the pressure sensor. 5. Replace the control board. 1. Check the drain hose for restrictions. 2. Start the washer and check for 120 VAC at the drain pump. Test 4: Inspect the wiring between the pressure sensor and the control board. Test 5: 1. Is the
  • Frigidaire ATF8000FS | Data Sheet - Page 4
    Test Check Test Correction Test 6: Test 7: Test 8: Test 9: Test 10: Test 11: Test 12: Test 13: Test 14: Test 15: 1. Is the loading door closed? 2. In the J2 plug on the control, measure voltage from the black wire to ground with power on. 1. Remove the door lock assembly and measuere the
  • Frigidaire ATF8000FS | Data Sheet - Page 5
    code d'erreur s'affiche à l'écran par un E suivi de deux chiffres, d'un chiffre et d'une lettre ou de deux lettres. La commande retentit et les voyants lumineux Door Lock, Wash, Rinse, et Final Spin Le code d'erreur s'annule. • Sortez du mode diagnostic pour retourner la machine à laver en mode de
  • Frigidaire ATF8000FS | Data Sheet - Page 6
    de la position démarrer. La commande signale le dernier code d'erreur. Quitter le mode diagnostic Il existe deux options pour quitter le mode test de diagnostic et retourner au fonctionnement normal de la machine à laver. a) Débranchez le cordon d'alimentation, attendez 5 à 8 secondes, ensuite
  • Frigidaire ATF8000FS | Data Sheet - Page 7
    E21 E23 E24 E31 E35 E36 E41 E43 E44 E45 E46 E47 E48 E52 E56 E57 E58 E59 E5A E5B E5C E5D E5E E5F E66 E67 E68 E71 E74 E75 E76 E82 E83 E91 E93 E94 E95 E97 E98 EB1 EB2 EB3 EF1 EF2 EBE EBF EF5 Défectuosité Tableau de code d'erreur
  • Frigidaire ATF8000FS | Data Sheet - Page 8
    . 7. Modèles Better, replacez le capteur de pression. Si le problème persiste, passez à l'étape 8. 8. Remplacez la carte de commande. Test 2: 1. Est-ce que de l'eau fuit de la machine à laver ? Oui. Corrigez la fuite d'eau. Non. Passez à l'étape (2) 2. Est-ce que l'air fuit dans le système de
  • Frigidaire ATF8000FS | Data Sheet - Page 9
    13: 1. Demandez que le fournisseur d'électricité vérifie la fréquence de l'entrée d'alimentation. Si elle est correcte, remplacez la carte de commande. Test 14: 1. Vérifiez la résistance de l'élément chauffant. Elle doit être d'environ 14 Ohms. 2. Vérifiez la résistance entre la mise à la terre et
  • Frigidaire ATF8000FS | Data Sheet - Page 10
    , luego suelte los botones. • Gire la perilla de programa en sentido horario 7 veces desde la Posición Inicio. El control señalará el último código de error. • Presione y mantenga presionados los botones Opciones e Inicio/Pausa durante 3 segundos. El código se borrará. • Salga del Modo Diagn
  • Frigidaire ATF8000FS | Data Sheet - Page 11
    sus manos adentro cuando está rotando el tambor. 8. Gire la perilla de programa siete (7) veces desde la posición de inicio. El control señalará el último código de error. Cómo Salir del Modo Diagnóstico Hay dos opciones para salir del modo Prueba de Diagnóstico y volver la lavadora a operaci
  • Frigidaire ATF8000FS | Data Sheet - Page 12
    fría supera el límite. Mangueras de agua caliente y fría cambiadas. E82 Problema de control de la consola. Cambiar el tablero de control. E83 Problema de control de la consola. Cambiar el tablero de control. E91 Error de comunicación entre el tablero de interfaz de usuario y el tablero de
  • Frigidaire ATF8000FS | Data Sheet - Page 13
    de presión está en mal estado. Cambie el interruptor de presión. Si esto no corrige el problema, vaya al paso 8. 8. Cambie el tablero de control. Test 2: 1. La lavadora, ¿pierde agua? Sí. Corrija la pérdida de agua. No. Vaya al paso (2) 2. ¿Hay una pérdida de aire en el sistema de campana de
  • Frigidaire ATF8000FS | Data Sheet - Page 14
    . Verifique el cierre de la puerta. Si está en buen estado, cambie el interruptor de la puerta. 120 voltios. Cambie el tablero de control. Test 7: 1. Quite el bloqueo de la puerta y mida la resistencia del Corto o abierto. Cierre de puerta defectuoso. circuito de rastreo de fases (PTC). Lectura
  • Frigidaire ATF8000FS | Data Sheet - Page 15
  • Frigidaire ATF8000FS | Data Sheet - Page 16
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Washer Tech Data Sheet
This information is intended for Qualified Technicians Only.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING
Please Return This Sheet to its Envelope in the Product for Future Reference
Contents
Page
Error code explanation
..............................................
1
Diagnostics
.............................................................
1
Error Code Chart
.......................................................
2
Tests
......................................................................
3-4
Français
.................................................................
5-8
Español
...............................................................
9-14
6000 Wiring Diagram
................................................
15
7000 Wiring Diagram
................................................
16
READING ERROR CODES:
1. Wake the washer by pressing any button.
2. Wait 5 seconds.
3. Press and
HOLD
the
Start/Pause
and
Cancel
buttons simultaneously.
As long as the buttons are held, the failure code will appear in the display as an
E
followed by two numbers, a number and a letter or two letters. The
control will beep and the
Door Lock, Wash, Rinse,
and
Final Spin
indicator lights will flash.
T
roubleshoot the problem by using chart
s on the p
ages 3-5.
Quick Check
I
f there is no error displayed and the washer momentarily starts then turns back off:
1.
Listen for a relay closure inside the motor control shortly after the
Start/Pause
key is pressed. If this happens, the motor control has
power.
2.
Check the 5 pin connector wiring between the console control and the motor control.
NOTE:
During normal operation, the display may show:
“
cd
” - cool down (Sanitary cycle)
“
do
” or “
dr
” - door problem.
“
Err
” - an error has been detected.
“
LOC
” - control lock is activated.
“
PAU
” - cycle has been interrupted.
To clear latest stored error code:
•
Turn the
Program Knob
to the
st
art position,
Spin Only.
•
Press
Start/Pause
to start the cycle and save it.
•
Press
Cancel
to stop the cycle and turn off the LEDs.
•
Press
Cancel
again to turn on the LEDs.
•
Within 5 seconds, press and hold the
Option
and
Start/Pause
buttons until LEDs start sequentially chasing, then release buttons.
•
Turn the program knob clockwise 7 clicks from the
S
t
art Position. The control will signal the last error code.
•
Press and hold the
Options
and
Start/Pause
buttons for 3 seconds. The code will be cleared.
•
Exit Diagnostic Mode to return the washer to normal operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 or 3 clicks after the
S
t
art Position. Press
Options
and
Start/Pause
buttons
together for a few seconds until wash cycle LEDs appear.
Diagnostic Test
The diagnostic test is used to check individual component function only.
T
O ST
ART THE TEST
:
•
Turn the
Program Knob
to the
st
art position,
Spin Only.
•
Press
Start/Pause
to start the cycle and save it.
•
Press
Cancel
to stop the cycle and turn off the LEDs.
•
Press
Cancel
again to turn on the LEDs.
•
Within 5 seconds, press and hold the
Options
and
Start/Pause
buttons until LEDs start sequentially chasing, then release
buttons.
1.
All the LEDs will sequentially light. Pressing a button below a light cluster will light all the LEDs in that cluster at one time to confirm functionality.
2.
Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the
detergent compartment.
3.
Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach
compartment.
4.
Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold water should enter through
the softener compartment.
5.
Turn the program knob (4) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened. When the door
is opened, the drum light should turn on.
6.
Turn the program knob (5) clicks from the start position. The washer will fill and tumble. Once tumbling has started, the Boost Heater (if so equipped)
will turn on.
7.
Turn the program knob (6) clicks from the start position. The drain pump & door lock solenoid will activate and the washer will operate in high spin.
SAFETY
W
ARNING:
If power is removed during this test, the door can be opened. To prevent injury,
DO NOT
put your hands inside when the tub
is rotating.
8.
Turn the program knob (7) clicks from the start position. The control will signal the last error code.
Exiting Diagnostic Mode
There are two options for exiting the Diagnostic Test mode and returning the washer to normal operation:
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 or 3 clicks after the
start position. Press
Options
and
Start/Pause
buttons together for a few seconds until wash
cycle LEDs appear.
If a situation arises where you cannot exit the Diagnostic mode as described above and the bank of 5 LED’s on the right end remain ON
regardless of Program Knob position, a combination of pushed buttons may have caused the control to enter a special factory test
mode. Disconnect power to reset the control to return washer to normal operation is this occurs.
134
8797
00
A
(0
702
)