Frigidaire CGEF3032MF Installation Instructions (All Languages)
Frigidaire CGEF3032MF Manual
 |
View all Frigidaire CGEF3032MF manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire CGEF3032MF manual content summary:
- Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 1
Hz. Systems) INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 2
to the Consumer Keep these instructions with your owner's guide for future reference. • As when using any appliance generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Manual, read it carefully. • Be sure your range is installed and grounded - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 3
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS (For 4 Wire, 60 Hz. Systems) B. Drill Pilot Holes and Fasten (CSA Standard (C22.1 Part 1 -- latest edition) -- and any local electrical code requirements. Locate outlet 6" above the floor in the wall behind the range. This appliance may be connected by - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 4
to the Use & Care Manual for cleaning instructions. If removing the range is necessary for cleaning or appliance. Refer to the warranty in your Use & Care Manual for our tollfree service number and address. Please call or write if you have inquiries about your range product and/or need to order parts - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 5
PAR L'INSPECTEUR EN ÉLECTRICITÉ. LISEZ ET CONSERVEZ CES INSTRUCTIONS POUR CONSULTATION FUTURE. Dimensions et espaces libres 1. Laissez ées doivent être appliquées. Les distances données sont minimales. La surface de support doit être solide et au niveau. *762mm (30") MINIMUM D'ESPACE LIBRE DOIVENT Ê - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 6
instructions au consommateur. Note importante au consommateur Conservez ces instructions avec votre guide ou un technicien de service qualifié. • Assurez-vous support de contre-renversement doit aussi être déplacé et installé avec la cuisinière si celle-ci est relocalisée. Des instructions - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 7
systèmes 60 Hz à 3 ou 4 fils)requis entre le bas de la cuisinière et la patte d'ajustement afin de permettre un espace pour le support. Utilisez un niveau à bulle pour vérifier vos ajustements. Glissez la cuisinière vers sa position. Vérifiez visuellement que la patte de mise à niveau arrière - Frigidaire CGEF3032MF | Installation Instructions (All Languages) - Page 8
vérifiez les raccordements électriques. Voyez les pages 2 et 3 pour les instructions correctes d'ancrage. Avant que vous ne fassiez un appel de service Lisez "Avant d'appeler" et les sections de notices d'opération de votre Guide d'utilisation et d'entretien, ils peuvent vous sauver temps et argent
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS
(For 4 Wire, 60 Hz. Systems)
1
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
P/N
316259203 (0109)
C
learances and Dimensions
1.
Provide adequate clearances between the range and adjacent combustible surfaces.
2.
Location—Check location where the range will be installed. Check for proper electrical supply, and the stability
of the floor.
3.
Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must
be solid and level.
*
30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE
BOTTOM OF AN
UNPROTECTED WOOD OR METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS
PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28
MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020" COPPER. 0" CLEARANCE IS THE
MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO
PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE
SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE
PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A
MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
English 1-5
Français - Pages 5-8