Frigidaire FBD2400KQ Wiring Diagram (All Languages)

Trouble Shooting Tips

Tub and Door Seal

The door seal is pressed into the tub channel for

an interference fit. Center the gasket (marked on

back) at the tub top center and press in place

Product Specifications

Separate Circuit..15 amp min.- 20 amp max.

Motor (Amps)

...........................................

1.1

Heater Wattage

.......................................

900

Total Amps (load rated)

.........................

10.0

Water Supply

Suggested minimum incoming water

temperature

.............................

120°F (49°C)

Pressure (PSI) min./max

. ...................

20/120

Connection (NPT)

.....................................

3

/

8

"

Consumption (Normal Cycle)

.......................

................................

7.2 U.S. gal., 27.3 liters

Always disconnect the dishwasher from the electrical power source before adjusting or

replacing components.

Personal Injury Hazard

without stretching or bunching. The gasket takes

a short turn at the bottom of the tub channel

before ending at the channel end wall.

Short Turn

Gasket Cross Section

Mounting

Rib

Tub

Interior

020905

Exploded View of Wash System

Drain Hose

(32" minimum

height)

Incoming Water Supply

Nut

Lower Spray Arm/Tower Assembly

Motor

Bracket

Sump Retainers (4)

Water Inlet Tube

Water Valve

Sump

Connector Hose and Clamps

Drain Motor

Volute Cover

Soil Director

Filter

Heating Element

The drain hose must have a loop at a

minimum

height of 32 inches

in order to insure proper

drainage.

To remove the main circulation (circ) pump

first disconnect the wiring harness connections

located at the circ pump’s motor, remove the

two screws tha hold the motor bracket, and

remove the motor bracket by sliding it away

from the sump.

The motor and pump can then

slide out of the sump.

Pump Assembly

The pump assembly is driven by a

synchronous motor. Rotation is in the

counterclockwise direction at 3600 RPM. The

motor drives a pump which supplies 100 percent

filtered water at a rate to approximately 12 GPM.

Draining is accomplished by using a small

separate synchronous drain pump mounted to

the side of the sump. The drain pump is

connected to the main pump by a small rubber

hose. The drain check valve is located at the

discharge end of the drain pump. The drain hose

is attached by a worm gear clamp to the discharge

end of the drain pump.

Circulation

Motor Assembly

Electrical

Rating

.....................................

120 Volts, 60Hz

Check the list below each symptom.

Repair or replace defective components as encountered.

Symptom. . .Dishwasher will not operate

when turned on (wait at least 90 seconds).

1. Fuse (blown or tripped).

2. 120 VAC supply wiring connection faulty.

3. Timer (contacts open or defective)

4. Motor (inoperative).

5. Door switch (open contacts).

6. Door latch not making contact with door

switch.

7. Selector switch (open contacts).

Symptom. . .Motor hums but will not start

or run.

1. Motor (bad bearings or locked rotor).

2. Motor stuck due to prolonged

non-use.

Symptom. . .Motor trips out on internal

thermal overload protector.

1. Improper voltage.

2. Motor shaft binding.

3. Motor windings shorted.

4. Glass or foreign items in pump.

Symptom. . .Dishwasher runs but will not

heat.

1. Heater element (open).

2. Timer defective.

3. Wiring or terminal defective.

Symptom. . .Dishwasher will not pump out.

1. Drain restricted.

2. Timer contact defective.

3. Defective drain pump.

4. Air lock in drain hose.

5. Blocked impeller.

6. Open windings.

Symptom. . .Dishwasher will not fill with

water.

1. Water supply turned off.

2. Defective water inlet fill valve.

3. Check fill valve screen for obstructions.

4. Defective float switch.

5. Timer contact defective.

6. Wiring defective.

7. Float stuck in “UP” position.

Symptom. . .Timer does not advance.

1. Timer motor (stalled or open.)

2. Check timer for power to timer motor.

3. Timer shaft binding to or knob interference

with escutcheon.

Symptom. . .Dishwasher water siphons out.

1. Drain hose (high) loop too low--must be a

minimum height of 32 inches.

2. Drain line connected to a floor drain not

vented. (Install air gap at counter top.)

Frigidaire FBD2400KQ Wiring Diagram (All Languages)

Frigidaire FBD2400KQ Manual

Frigidaire FBD2400KQ manual content summary: