Frigidaire FFAP5033W1 Complete Owners Guide - Page 6

continued

Page 6 highlights

Operating Instructions Operating Instructions (continued) 5. The Filter reset light will illuminate after 250 hours of operation. At this time refer to the care and cleaning section to remove and clean the filter. Once the filter has been cleaned and replaced, simply press the Filter reset button to extinguish the light. 6. The TIMER function enables you to either Delay Start or Delay Stop the unit in the choice from 0.5 hour to 24 hours. If the unit is running, then selecting Timer will turn the unit off in the hours that will be set (Delay Stop). If the unit is off, then selecting Timer will turn the unit on in the hours that will be set (Delay Start). TIMER setting: First press TIMER button, then adjust timer setting, by tapping or holding the or button to change the delay timer at 0.5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining (8,7.5,7, etc.) until the unit either starts or stops. For the Delay Start, the fan speed and humidity maintained will be the same as previous setting. After TIMER setting finishes, pressing TIMER button again at any time will stop the TIMER function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens the above steps have to be repeated. NOTE: 1. Before entering TIMER setting, make sure power is being supplied to the unit. 2. Before entering TIMER setting, make sure pressing HUMIDITY or button sets one desired room humidity first. 7. Press PUMP button, the unit will enter water pump mode. Pump Mode Indicator will be on. When the water tank is full of water, the pump will start to pump water automatically. The pump will stop automatically after the water tank have been empty. NOTE: ‡3XPSGUDLQKRVHPXVWEHZHOOFRQQHFWHGIRUWKLVPRGH ‡,IWKH3XPSLQGLFDWRUDQG%XFNHW)XOOLQGLFDWRUIODVKVLPXOWDQHRXVO\DIWHUSUHVVLQJWKH3XPSEXWWRQFKHFNLIWKH pump drain hose in the bucket is installed properly. 6 2019 Electrolux Home Products, Inc. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13

Operating Instructions
(continued)
1. Before entering TIMER setting, make sure power is being supplied to the unit.
2. Before entering TIMER setting, make sure pressing HUMIDITY
or
button sets one desired room humidity first.
NOTE:
Ç. Press PUMP button, the unit will enter water pump mode. Pump Mode Indicator will be on. When the water tank is
full of water, the pump will start to pump water automatically. The pump will stop automatically after the water tank have
been empty.
Operating Instructions
NOTE:
± ÈXÀ´ G»³²Q K¸V· ÀXV¹ ¼· Z·µµ ¶¸QQ·¶¹·G º¸» ¹K²V À¸G·Ä
± ɺ ¹K· ÈXÀ´ ²QG²¶³¹¸» ³QG ÊX¶Á·¹ ËXµµ ²QG²¶³¹¸» ºµ³VK V²ÀXµ¹³Q·¸XVµ\¿ ³º¹·» ´»·VV²QJ ¹K· ÈXÀ´ ¼X¹¹¸Q¿ ¶K·¶Á ²º ¹K·
pump drain hose in the bucket is installed properly.
6. The TIMER function enables you to either Delay Start or Delay Stop the unit in the choice from 0.5 hour to 24 hours.
If the unit is running, then selecting Timer will turn the unit off in the hours that will be set (Delay Stop). If the unit is
off, then selecting Timer will turn the unit on in the hours that will be set (Delay Start).
TIMER setting: First press TIMER button, then adjust timer setting, by tapping or holding the
or
button to
change the delay timer at 0.5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The
control will count down the time remaining (8,Ç.5,Ç, etc.) until the unit either starts or stops. For the Delay Start, the
fan speed and humidity maintained will be the same as previous setting. After TIMER setting finishes, pressing TIMER
button again at any time will stop the TIMER function. The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens the above steps have to be repeated.
6
2019 Electrolux Home Products, Inc.
All rights reserved.
5. The Filter reset light will illuminate after 250 hours of operation. At this time refer to the care and cleaning section
to remove and clean the filter. Once the filter has been cleaned and replaced, simply press the Filter reset button
to extinguish the light.