Frigidaire FFID2423RS Wiring Diagram - Page 1
Frigidaire FFID2423RS Manual
View all Frigidaire FFID2423RS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
for injury or damage of any kind arising from the use of this Service Products North America cannot be responsible, nor assume any liability, considered acceptable in the appliance repair trade. Electrolux Home Artwork: A02841501 Rev.001 P/N: A02841501 Rev.A This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally SERVICE DATA SHEET Electronic Series COLOR CODE BK............Black BU............Blue PK............Pink R Red Viol..........Violet W White Y Yellow R-Y.........Red/Yellow R-BK......Red/Black To start To delay start --------- To select a new cycle or option To cancel a cycle To cancel a cycle OPERATION DISPLAY CODES (LED) Close door fully to latch. Press START/CANCEL pad. Close door fully to latch. Press DELAY START pad to select desired delay time. Press desired cycle and/or option pad. The indicator lights will change. Press START/CANCEL within 15 seconds to begin cycle. Press START/CANCEL. Dishwasher will drain for 90 seconds, then shut off. Press and hold the RINSE HOLD or NO HEAT DRY pad for 3 seconds. To unlock, press and hold the RINSE HOLD or NO HEAT DRY pad for 3 seconds. WASHING---------- Wash portion of cycle. SANITIZED--------- The SANITIZED criteria has been met. Indicator light will switch off when door is opened. DRYING Drying portion of cycle. CLEAN Shows completion of cycle. Indicator light will switch off when door is opened. OPTION LED's Flashing- When ALL LED's are flashing this indicates power failure has occured. Press START/CANCEL pad and reslect desired options and cycles. BK P3- 6 BK P1 W P3- 7 BK P2- 1 W P2- 2 R P2- 3 Interval Number Description Interval Duration Sec. Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Washing LED Sanitize LED Drying LED Clean LED Notes WATER/SERVICE TEST The water/service test, (WST) is a special function initiated from the power failure mode or idle mode. While in power failure mode - simultaneously press the AIR DRY and START/CANCEL pads for 1 1/2 seconds. While in Idle Mode, simultaneously press HI-TEMP 1 Fill/Det. Dispenser 2 Fill 60 1 0 0 0 1 1 1 0 0 0 27 1 0 0 0 0 1 1 0 0 0 WASH and START/CANCEL pads for 6 seconds. 3 Wash/Heat/Det. Disp. 60 0 1 0 1 1 1 1 0 0 0 4 Pause 0.4 0 0 0 1 0 1 1 0 0 0 The dishwasher will then step through the test cycle per the 5 Wash/Heat 75 0 1 0 1 0 1 0 0 0 0 chart. Pushing the START/CANCEL 6 Wash/Heat/Det. Disp. 60 0 1 0 1 1 1 0 0 0 0 pad will advance the dishwasher 7 Drain 90 0 0 1 0 0 1 0 0 0 0 to the next step. 8 Dry 90 0 0 1 x 0 0 0 0 1 0 End State 0 0 000 0 0 10 1 X - denotes selectable option Clean LED stays on until door is opened or cycle is started USER INTERFACE SWITCH P- 5 W PUMP MOTOR DRAIN MOTOR W *THERMISTO R *RINSE AID LEVEL SENSE DISPENSER W *VENT SYSTEMS W WATER VALVE W HEATER W BU P3- 5 VI O P3- 4 Y P3- 9 Y P3-10 BK P2- 5 BK P2- 6 R- Y P3- 1 ELECTRONIC CONTROL BOARD R-BK P3- 2 FLO AT SWITCH PK P3- 3 HI-LIMIT THERMOST AT R P8 WIRING DIAGRAM *TURBIDITY SENSOR/ THERMISTOR DOOR SWITCH L1 BK NEUT W 120VAC 60HZ W *SOME MODELS Data Sheet. CYCLE SELECTION OPTIONS