Frigidaire FFTR2021TS Product Specifications Sheet - Page 3
Installation Specifications, Top Mount Refrigerator - ice maker
View all Frigidaire FFTR2021TS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Baseline FFTR2021T D/S/W/B TOP MOUNT REFRIGERATOR 20.4 CU. FT. Top View Recessed water line Recessed (ice maker models only) electrical outlet Allow 1" min. clearance at rear for proper air circulation and water / electrical connections Allow 3/8" min. clearance at sides and top for ease of installation When installing directly adjacent to wall, sufficient handle clearance required where handle may make contact with wall, to allow for 90° door opening* * When installing refrigerator adjacent to wall, cabinet or other appliance that extends beyond front edge of unit, 20" minimum clearance recommended to allow for optimum 140° door swing, providing complete crisper access and removal. (Absolute 3" minimum clearance will ONLY allow for 90°door swing which will provide limited crisper access with restricted removal.) 32" 29 5/8" 69" with 3/8" rollers 68 1/4" with 3/8" rollers Water line inlet location (left bottom rear) 28 1/2" 34 1/2" Power cord location (right bottom rear) Allow 60" min. (with doors 90° open) INSTALLATION SPECIFICATIONS • Product Shipping Weight (approx.) - 220 Lbs. • An electrical supply with grounded three-prong receptacle is required. The power supply circuit must be installed in accordance with current edition of National Electrical Code (NFPA 70) and local codes & ordinances. • Voltage Rating - 120V / 60 Hz • Connected Load (kW Rating) @ 120 Volts = 0.72 kW • Amps @ 120 Volts = 6.0 Amps • Always consult local and national electric & plumbing codes. • Floor should be level surface of hard material, capable of supporting fully loaded refrigerator. • Minimum 3/8" clearance required for sides and top of refrigerator with 1" clearance at rear to allow for ease of installation, proper air circulation, and plumbing / electrical connections. • When installing refrigerator adjacent to wall, cabinet or other appliance that extends beyond front edge of unit, 20" minimum clearance recommended to allow for optimum 140° door swing, providing complete crisper access and removal. (Absolute 3" minimum clearance will ONLY allow for 90° door swing which will provide limited crisper access with restricted removal.) • To ensure optimum performance, do not install in areas where temperature drops below 55° F or rises above 110° F and avoid installing in direct sunlight or close proximity to range, dishwasher or other heat source. • For proper ventilation, front grille MUST remain unobstructed. • Recess electrical outlet when possible. • Optional Ice Maker Kit (PN # IM116) available for installation in ice maker-ready models only. • Water recess on rear wall recommended to prevent water line damage. • Water Pressure - Cold water line must provide between 30 and 100 pounds per square inch (psi). • Copper tubing with 1/4" O.D. recommended for water supply line with length equal to distance from rear of unit to household water supply line plus 7 additional feet. Optional Water Supply Installation Kits available. • Adjustable front rollers to assist with door alignment. OPTIONAL ACCESSORIES • Ice Maker Kit - (PN # IM116). Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes. Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com / frigidaire.ca. Specifications subject to change. Accessories information available on the web at frigidaire.com / frigidaire.ca USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FFTR2021T 10/17 © 2017 Electrolux Home Products, Inc.