Frigidaire FGSS2335TF Installation Instructions

SERVICE DATA SHEET

A01461102

ICE & WATER - AUTOMATIC DEFROST

SIDE BY SIDE - R134a

CAUTION

All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation;

it will char at 200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner.

DIAGNOSTIC MODE

Activate:

Press ^ and

V

temperature pads for up to 10 sec. simultaneously. Press

+

to advance through tests.

Deactivate:

Press

+

for up to 10 sec. Diagnostic Mode will automatically deactivate after 5 min. of inactivity.

Note: Silence alarm.

• Tests marked with “*” may not be applicable to this unit and will not be displayed in Diagnostic Mode.

• Tests displayed in diagnostic mode but not described below are for internal purposes only; advance through.

• View UI display for “on,” “off,” “CL,” “OP,” “SH,” “LO,” “HI” or numerical results of tests.

• Listen for operating sounds; feel for heat or air flow as appropriate to determine results of tests.

Test

To activate test:

Passing result

--

First Screen

--

All LED lights on UI illuminated

--

Second Screen

--

All segments on UI temperature displays illuminated

--

Third Screen

--

Blank UI display, no lights illuminated, no shadowing; “-” and “+”

blinking on FF display side to show location.

28

Dispenser Paddle

Press disp. paddle

“on” on UI when depressed; “off” when released

46

Humidity Sensor

Activates automatically

“OP” if open, “SH” if short

AC Heater System: Displays %RH

DC Heater System: “HI” – heater should be on

“Lo” – heater should be off

%RH is displayed when humidity is between “Lo” and “HI” values;

heater could be on or off.

47*

Dispenser

Pocket Heater

Press set

AC Heater System: “--” ; test not available

DC Heater System: heater on when “on”, off when “off”

1*

Standard Compressor

and Condenser Fan

Press set

Compressor and Condenser Fan running when “on”; stopped when “off”

2

Defrost Heater

Press set

Defrost limit switch must be closed; verify “CL” in test 26.

Feel for heat from defrost heater when “on”.

If “OP” in test 26, heater will not activate.

8

Water Valve

(Dispenser)

Press set

Be prepared to collect water at dispenser.

Water dispenses when “on”; stops when “off”

10

Auger Motor

Press set

FZ door must be closed.

Motor running when “on”; motor stopped when “off”

11

Cube/Crush

Solenoid

Press set

Do not leave solenoid in activated state.

Solenoid activated when “on”; deactivated when “off”

41*

Perfect Temp

Drawer (PTD)

Press set

PTD UI illuminated when "on", off when "off"

12*

VCC Condenser Fan

Press set

Fan running when “on”; stopped when “off”

38*

VCC Compressor

Press set

Compressor running when “on”; stopped when “off”

13

FF Light (LED Models)

Press set

FF Lights on when "on"; off when "off"

15

Evaporator Fan

Press set

Fan running for

minimum of 10 sec.

when “LO” or “HI”; stopped when

“off”. Feedback failure if fan starts but runs less than 10 sec. Listen for

speed change from “LO” to “HI”.

20

FZ Light (LED Models)

Press set

FZ Lights on when "on"; off when "off"

22

Damper

Press set

With inspection mirror, observe damper open when “OP”; closed when “CL”

36

Ice Chute Door

Depress ice chute

door or press set

“OP” on UI when manually opened; “CL” when closed. Or, using “set”,

“OP” on UI when fully opened or "CL" when fully closed by the motor.

23

FF Door

Open/close FF door

“CL” on UI when door closed; “OP” when open

24

FZ Door

Open/close FZ door

“CL” on UI when door closed; “OP” when open

26

Defrost Limit Switch


“CL” on UI when closed; “OP” when open

29

FF Thermistor


UI shows temperature sensed by FF thermistor; pass if within 10°F of

temperature measured with gauge at mid-level FF thermistor location.

“OP-” if open; “SH-” if short

30

FZ Thermistor


UI shows temperature sensed by FZ thermistor; pass if within 10°F of tempera-

ture measured with gage at FZ thermistor location.

“OP” if open; “SH” if short

33

Ambient Thermistor

@ Main Board


UI shows temperature sensed at main board; pass if within +20°F/-10°F

of temperature measured with gauge at main board location.

“OP” if open; “SH” if short

34

Ambient Thermistor

@ UI


UI shows temperature sensed at UI; pass if within +20°F/-10°F of tem-

perature measured with gauge at UI location. “OP” if open; “SH” if short

39

Evaporator Thermis-

tor


UI shows temperature sensed at main board; pass if within +20°F/

-10°F of temperature measured with gauge at evaporator thermistor

location. “OP” if open; “SH” if short

0-

Firmware Parameters

Press set

Displays digit sequence; record

2-

Main Board Firmware

Press set


4-

UI Firmware

Press set


Variable Capacity Compressor (VCC) Diagnostics (select models)

If test 38 fails, diagnose as follows:

Replace Inverter

→

Check at the connector

from main control into

the inverter (typically

BLK and RED wires)

Is Inverter receiving

10-15 VAC

and 1-5 VDC from

Main Control?

→

Check at Main Control

Board

(BLK/WHT and RED/BLK wires)

Is Main Control

sending 10-15 VAC

and 1-5 VDC to

Inverter?

no

→

Check at the connector from

the service cord into the

inverter (typically PUR and

WHT wires.)

Is Inverter receiving 115

VAC from power supply?

yes

•

Check voltage supply.

•

Check and repair

service cord

wiring

and connections.

no

Identify and repair

damaged wires or

poor

connections between

Main Control and

Inverter

yes

→

Remove inverter box

from the compressor

and check resistance

across compressor

winding pairs as shown.

Is resistance across

all winding pairs

equal?

yes

Replace Compressor

no

→

Check connections

from Inverter

to

Compressor

Are connections

from Inverter to

Compressor intact?

yes

yes

Identify and repair

damaged wires or poor

connections between

Inverter and Compressor.

no

VCC Resistance Check

Check resistance between terminals

1 and 2, 2 and 3, 3 and 1.

If all resistances are equal,

compressor is operative.

Replace Main Control

no

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT

0

° F FREEZER & 37° F FRESH FOOD

(2500 ++ V5)

Type A with Run/

Start Capacitor

65°F (18°C) Ambient

90°F (32°C) Ambient

Variable Speed

Standard

Variable Speed

Standard

Operating Time

74 to 84%

32 to 40%

100%

55 to 65%

Freezer Temperature

-2° to 2° F

-19° to -17° C

0° to 4° F

-18° to -16° C

-1° to 3° F

-18° to -16° C

-1° to 3° F

-18° to -16° C

Refrigerator Temperature

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

Low Side Pressure (cut-in)

5 to 12 psig

43 to 83 kPa

5 to 12 psig

43 to 83 kPa

N/A

5 to 12 psig

43 to 83 kPa

Low Side Pressure

(cut-out)

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

High Side Pressure

(last

1

/

3

cycle)

90 to 105 psig

621

to 724 kPa

90 to 115 psig

621 to 793 kPa

120 to 135 psig

827 to 931 kPa

130 to 155 psig

896 to 1069 kPa

Wattage (last

1

/

3

cycle)

50 to 60

90 to 130

60 to 70

100 to 140

Amps (running)

0.5 to 0.9

0.7 to 1.1

0.6 to 1.0

0.8 to 1.2

Base Voltage

115 vac (127 vac max)

DEFROST SPECIFICATIONS

Cabinet Size

Thermostat

Heater

Cut-in

Cut-out

Watts

Ohms

23’ CD, 26’

25° F (-4° C)

47° F (8° C)

450

30

Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time.

CONDENSER FAN MOTOR

Watts

RPM

Amps

3.1

1100 CW Opposite Shaft

0.03 Running

ERROR CODES

SPECIAL MODES

Display

Interpretation

Mode

Display

Activate/Deactivate

(press for up to 10 sec. simultaneously)

FZ

FF

FZ

FF

--

OP-

Open FF

mid-level thermistor

Manual

Defrost

d

F

+

and

-

/same to deactivate

OP

--

Open FZ thermistor

Display/

Showroom

77

77

^

and

-

/set

Sabbath

Sb

Sb

V

and

+

/same to deactivate

--

SH-

Shorted FF

mid-level thermistor

Diagnostic

No FF or FZ display,

all UI LEDs on.

^

and

V

/+ to deactivate

Notes:

• Always check for pin back-outs, pinched or damaged wires before

replacing components.

• Determine whether failure is caused by the component, main control

board or wiring. Contact TID before replacing main control board.

• Refer to Service Manual for additional information.

SH

--

Shorted FZ thermistor

SY

CF

UI to Main Control

Board communication

failure; on start up

SY

CE

UI Main Control Board

communication error;

after a period in operation

SY

EF

Evaporator fan failure

OUT 1A

OUT 2A

OUT 1B

OUT 1B

ERF-2500++ V5

REFRIGERATOR

CONTROL

NTC 1 - FF

NTC 2 - FF

NTC

- FZ

DEFROST HEATER

DEFROST THERM.

NEUTRAL

CONTROL

GROUND

ICE FLAPPER

SOLENOID

+5V

+5V

+5V

DC

EVAPORATOR

FAN

M

DAMPER

MOTOR

M

FG

VCC(+12)

COM

VS

VCC

COMPRESSOR

CONDENSER

FAN

STANDARD

COMPRESSOR

M

COMMON

HIGH

LINE

AMBIENT

NTC

DEFROST SENSE

LINE

G5LE RELAY

LINE

NEUTRAL

AUGER

MOTOR

LINE

CUBE/CRUSHED

ICE GATE CONTROL

M

DOOR

SWITCH

NEUTRAL

LINE

LINE

J3-16

J3-3

J3-3

J3-

7

DISPENSER VALVE

PRIMARY VALVE

ICE MAKER

FILL VALVE

ICE MAKER FILL SWITCH

G8P RELAY

J4-B1-6

J4-B1-1

J4-B1-2

J4-B1-3

J4-A1-9

J4-A1-3

J4-A1-10

J4-A1-4

J4-A1-11

J4-A1-5

J2-

1

J3-

2

J3-1

J2-2

J1-4

J4-B1-4

J4-A1-6

J4-A1-7

J4-B1-5

J4-A1-13

J4-A1-14

J8-

5

J8-

6

J8-

7

J8-

8

JF-

1

JF-

2

JF-

3

JF-

4

ASSY_OUT

ASSY_IN

+5V

GROUND

+5V

RESET_FLASH

BKGD/MSJ

GROUND

J9A-1

J9A-2

J9A-3

VEE (+12V)

COMM

GROUND

ISOLATED

USER

INTERFACE

J1-1

J2-9

J2-10

J3-13

J3-14

J3-15

J3-16

J1-3

J2-7

NEUTRAL (SERVICE CORD)

NEUTRAL (CONDENSER FAN)

NEUTRAL (WATER VALVE 1)

NEUTRAL (NOT USED)

NEUTRAL (COMPRESSOR)

NEUTRAL (LED POWER SUPPLY)

NEUTRAL (DISPENSER & ICE MAKER VALVE)

LINE (SERVICE CORD)

LINE (Vcc COMPRESSOR)

ICE & WATER

DISPENSER

CONTROL

LED POWER

BOARD

J3-

1

J3-

4

J3-

3

NEUTRAL

FREEZER

LIGHTS

REFRIGERATOR

LIGHTS

FZR DOOR SW. SENSE

J3-9

J3-10

J2-12

J3-8

J3-11

J2-6

LINE

FF DOOR SW. SENSE

INCANDESCENT LIGHTING MODELS ONLY

FF DOOR SW. SENSE

REFRIGERATOR LIGHTS

FZR DOOR SW. SENSE

FREEZER LIGHTS

NEUTRAL

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION

IMPORTANT SAFETY NOTE

The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not

attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

IMPORTANT

If any green grounding wires are removed during servicing, they must be returned to their original position and

properly secured.

Frigidaire FGSS2335TF Installation Instructions

Frigidaire FGSS2335TF Manual

Frigidaire FGSS2335TF manual content summary: