Frigidaire FGUB2642LF Wiring Diagram (All Languages) - Page 1
Frigidaire FGUB2642LF Manual
UPC - 012505698453
View all Frigidaire FGUB2642LF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0° CONTROL SETTING Type A with Run/Start Capacitor 65°F (18°C) Ambient 90°F (32°C) Ambient Operating Time 74 to 84% 100% Freezer Temperature -5° to 2° F (-20° to -17° C) -1° to 3° F (-18° to -16° C) Refrigerator Temperature 34° to 39° F (1° to 4° C) 34° to 39° F (1° to 4° C) Low Side Pressure (cut-in) 5 to 12 psig (34 to 83 kPa) N/A Low Side Pressure (cut-out) -2 to 2 psig ( -14 to 14 kPa) -2 to 2 psig (-14 to 14 kPa) High Side Pressure (last 1/3 cycle) 85 to 95 psig (586 to 655 kPa) 120 to 135 psig (827 to 931 kPa) Wattage (last 1/3 cycle) 45 to 55 60 to 70 Amps (running) .6 to 1.1 .7 to .9 Base Voltage 115 vac (127 vac max) DEFROST SPECIFICATIONS Cabinet Size Thermostat Cut-in Cut-out Watts Heater Ohms 26' & 28' SD, 23' CD 25° F (-4° C) 47° F (8° C) 500 31 Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time. CONDENSER FAN MOTOR Watts RPM Amps 3.1 1100 CW Opposite Shaft 0.03 Running ICE MAKER SPECIFICATIONS Electrical 115 vac (127 vac max) Thermostat Opens at 48° F ( 9° C), Closes at 15° F ( -9° C) Heater Voltage 85 vac ICE MAKER CONNECTOR PLUG CONNECTIONS Wire Number Wire Color Connects to: 1 Green/Yellow Ground 2 Yellow Water Valve 3 Black Line 4 Light Blue Neutral important safety NOTE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance. IMPORTANT If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured. Caution All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner. NOTE This product comes equipped with an Adaptive Defrost Control (ADC). To activate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A "d" in the freezer temperature window and "F" in the refrigerator temperature window will display when the heater is activated. To deactivate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A "d" and "F" will be displayed until the defrost cycle is complete. IMPORTANT PLEASE RETURN THIS SHEET TO IT'S ORIGINAL LOCATION. service data sheet 240389643 ICE & WATER - AUTOMATIC DEFROST BOTTOM FREEZER - R134a Ice Maker Errors Displayed on "UI" ERROR Ice Ice Ice Ice Er IM/RAM Error (on POR only)Detection - on POR only. This error is detected as "no com/data link with IM" by ERF 2500++ system controller (PB). IP Invalid Protocol (this error is detected when the version of I/M pcb does not match version of 2500++ system controller) CE IM Com Lost only after POR(no communication between the I/M pcb and the 2500++ system controller.) t3 TH3 Error (open or short) This error is detected when the thermister has failed on the suction line of the I/M. Test 48C 49C 50C 51C 52C 54C 56C 55C Diagnostic Mode Activate: Hold FF (+) and FZ (+) for 5 sec. Freezer Recover Mode, "1" ok "Fr" Recovery mode, Icemaker in "off" state. (See Note) EEV On=Open Off=Closed , EEV must be in the open state for sealed system evacuation. Com Link "1" ok "ER" error Note: 57C 58C 59C See Service Manual for complete description. Fan test, on or off Ice level sensor switch test Fill limit switch test (See Note) TH1 Status "1" ok "ER" Replace 60C Freeze limit switch test (See Note) TH3 Status "1" ok "ER" Replace 61C Mold heater test, on or off 62C Finger evap heater, on or off 63C Water valve test (See Note) 64C De-activate: Hold FF (+) for 5 sec. IM evap heater test EEV test Harvest motor system test (See Note) Software version System Error Codes Displayed on "UI" ERROR Test OP or 2 Freezer Sensor OPEN 1 SH or 3 Freezer Sensor SHORTED 2 OP or 2 FF Sensor OPEN 3 SH or 3 FF Sensor SHORTED 8 SY EF Evaporator Fan Circuit 9 SY CE Communication error 10 SY CF Communication error 11 dF In Manual Defrost 41 12 To initiate manual defrost press and hold, for 5 sec. FF(+) and FF(-), (d) and (f) 38 will be displayed. 15 Diagnostic Mode Activate: FZ (+) and FZ (-) for 5 sec. Standard compressor Defrost heater FF lighting Water valve,water disp. FZ lighting Auger motor Cube/crush solenoid Perfect Temp Drawer VCC Condensor fan VCC Compressor Note: See Service Manual for complete description. 22 Damper 23 Fresh food door 24 Freezer door 26 Defrost limit switch 28 Dispenser paddle 36 Ice door 29 FF Thermistor 30 FZ Thermistor 33 Ambient Thermistor 0- Software version Evaporator fan De-activate: Hold FF (+) for 5 sec. FREEZER iCE MAKER INFORMATION Test Cycling: Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Adjustment Motor Gear Water Fill Volume: The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. Mounting Plate Screw LINE POWER BLK ICE MAKER BLK BRN P-3 THERMAL CUT-OUT ICE MAKER GRN / YEL P-1 MOLD BLK MOTOR RED HOLD SWITCH NO YEL RED C NC THERMOSTAT NO BLK MOLD HEATER 165 WATTS BLU C NC NO SHUT-OFF SWITCH MOUNTING PLATE ICE MAKER C NC WATER FILL SWITCH LT. BLU GRN / YEL YEL RED LT. BLU YEL WATER VALVE N ICE MAKER TUR Mounting Plate Screws Timing Gear NEUTRAL P-4 P-2 FF Ice Maker (2419801)