Fujitsu MHT2060BH Manual/User Guide

Fujitsu MHT2060BH - Mobile 60 GB Hard Drive Manual

Get Fujitsu MHT2060BH - Mobile 60 GB Hard Drive PDF manuals and user guides
UPC - 000053779588
View all Fujitsu MHT2060BH manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu MHT2060BH manual content summary:

  • Fujitsu MHT2060BH | Manual/User Guide - Page 1
    CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E203-02EN 3-1
  • Fujitsu MHT2060BH | Manual/User Guide - Page 2
    Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of
  • Fujitsu MHT2060BH | Manual/User Guide - Page 3
    3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation Figure 3.2 illustrates the allowable orientations for the disk drive. gravity (a) Horizontal -1 (b) Horizontal -1 (c) Vertical -1 (d) Vertical -2 gravity (e) Vertical
  • Fujitsu MHT2060BH | Manual/User Guide - Page 4
    Conditions (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal Ground (SG). IMPORTANT Use M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.3. The tightening torque must be 0.49N•m (5kgf•cm
  • Fujitsu MHT2060BH | Manual/User Guide - Page 5
    3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.4. For breather hole of Figure 3.4, at least, do not allow its around φ 2.4 to block. Figure 3.4 Location of breather C141-E203-02EN 3-5
  • Fujitsu MHT2060BH | Manual/User Guide - Page 6
    in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from
  • Fujitsu MHT2060BH | Manual/User Guide - Page 7
    Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect
  • Fujitsu MHT2060BH | Manual/User Guide - Page 8
    HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of the screw strictly. M3 0.49N•m (5 kgf•cm). - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO
  • Fujitsu MHT2060BH | Manual/User Guide - Page 9
    with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.8 shows the locations of these connectors and terminals. SATA interface PCA and power connectors Figure 3.8 Connector locations C141-E203-02EN
  • Fujitsu MHT2060BH | Manual/User Guide - Page 10
    for host system Table 3.2 lists the recommended specifications for the host interface connectors. Table 3.2 The recommended connector specifications for the host system Segment SATA interface and power supply Name Host receptacle Model (Manufacturer) 67492-0220 (Molex) or compatibles 3-10
  • Fujitsu MHT2060BH | Manual/User Guide - Page 11
    be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: • When plugging
  • Fujitsu MHT2060BH | Manual/User Guide - Page 12
    This page is intentionally left blank.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
C141-E203-02EN
3-1
CHAPTER 3 Installation Conditions
3.1
Dimensions
3.2
Mounting
3.3
Cable Connections
This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.