Fujitsu MHV2080AS Maintenance Manual - Page 30

Spare Parts, 2.2 Disk Drive Removal, Removal and Replacement Procedure

Get Fujitsu MHV2080AS - Extended Duty Mobile 80 GB Hard Drive PDF manuals and user guides View all Fujitsu MHV2080AS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Removal and Replacement Procedure 2.1 Spare Parts See Table 2.1 for the model and parts numbers to order the replacement disk drive. Table 2.1 Model and parts numbers Model Name MHV2080AS MHV2060AS MHV2040AS Capacity (user area) 80GB 60GB 40GB Mounting screw M3 Depth 3 M3 Depth 3 M3 Depth 3 Order No. CA06531-B708 CA06531-B706 CA06531-B704 2.2 Disk Drive Removal The method and procedures to demount the disk drive to check the jumper terminal, change the jumper position, or replace the device differ depend on the system cabinet structure. Therefore, for actual working procedures, the specific conditions necessary for each system must be determined. The general removal procedures, with notes, are as follows. a) Disconnect the power-interface cable. b) Remove the screws that attach the drive and remove the drive from the system cabinet. c) When storing or transporting the drive, pack it an antistatic bag in compliance with section 1.1.2 (5) d. and (5) e.. To protect the device from damage and prevent the worker getting hurt, observe the following cautions and precautions in Subsection 1.1.1. Damage or Device damage 1. Perform any removal after the system power is completely disconnected. The cable must not be disconnected and the screws that attach the drive must not be removed with the power ON. 2. Do not move the drive and attach or detach the connector until it comes to a complete stop (about 30 s after the power is turned OFF). 3. Perform the human body grounding to discharge any static electricity from your body (Be sure to wear a wrist strap). 2-2 C141-F073

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Removal and Replacement Procedure
2-2
C141-F073
2.1
Spare Parts
See Table 2.1 for the model and parts numbers to order the replacement disk
drive.
Table 2.1
Model and parts numbers
Model Name
Capacity
(user area)
Mounting screw
Order No.
MHV2080AS
80GB
M3 Depth 3
CA06531-B708
MHV2060AS
60GB
M3 Depth 3
CA06531-B706
MHV2040AS
40GB
M3 Depth 3
CA06531-B704
2.2
Disk Drive Removal
The method and procedures to demount the disk drive to check the jumper
terminal, change the jumper position, or replace the device differ depend on the
system cabinet structure.
Therefore, for actual working procedures, the specific
conditions necessary for each system must be determined.
The general removal
procedures, with notes, are as follows.
a)
Disconnect the power-interface cable.
b)
Remove the screws that attach the drive and remove the drive from the
system cabinet.
c)
When storing or transporting the drive, pack it an antistatic bag in
compliance with section 1.1.2 (5) d. and (5) e..
To protect the device from damage and prevent the worker getting hurt, observe
the following cautions and precautions in Subsection 1.1.1.
Damage or Device damage
1.
Perform any removal after the system power is completely
disconnected.
The cable must not be disconnected and the
screws that attach the drive must not be removed with the
power ON.
2.
Do not move the drive and attach or detach the connector until
it comes to a complete stop (about 30 s after the power is
turned OFF).
3.
Perform the human body grounding to discharge any static
electricity from your body (Be sure to wear a wrist strap).