Garmin AIS 800 Installation Instructions - Page 3

Wire Garmin Wire Color Red Yellow Black Purple Gray Blue Brown Green Garmin Wire Function Power ACC on Power ground RxA (+) RxB (-) TxA (+) TxB (-) Silent-mode (receive only),optional Appendix Specifications Dimensions (W x H x D) Weight Operating temperature range Storage temperature range Water rating Power input Current draw Fuse NMEA 2000 LEN Transmit power Antenna port impedance Wireless frequency/protocol Compass-safe distance 175 x 142.3 x 54.5 mm (6.9 x 5.6 x 2.1 in.) 414 g (0.9 lbs.) From -15° to 55°C (from 5° to 131°F) From -20° to 75°C (from -4° to 167°F) IEC 605290 IPX71 12 to 24 Vdc, 2 A max. 12 Vdc: less than 400 mA 24 Vdc: less than 250 mA 5 A, 125 V fast-acting 2 5 W (1 W remote switchable by authorities) 50 ohm 162 MHz @ 37 dBm nominal 40 cm (15 3/4 in.) NMEA 2000 PGN Information Type Receive PGN 059392 059904 060928 126208 Transmit 126992 059392 060928 126208 126464 126996 129038 129039 129040 129041 129794 Description ISO acknowledgment ISO request ISO address claim NMEA: Command, request, acknowledge group function System time ISO acknowledgment ISO address claim NMEA: Command, request, acknowledge group function PGN list Product information AIS class A position report AIS class B position report AIS class B extended position report AIS aids to navigation (AtoN) report AIS class A static and voyage related data Type PGN 129795 129797 129798 129802 129809 129810 Description AIS addressed binary message AIS binary broadcast message AIS SAR aircraft position report AIS safety related broadcast message AIS class B "CS" static data report, part A AIS class B "CS" static data report, part B Status LEDs LED VHF TX Error SRM Warning RX Only TX RX Power VHF TX, Error, Warning, and Power. State Description Solid A connected VHF radio is transmitting. Solid The device has encountered a critical error. You can connect the device to a computer, and use the AIS 800 setup software to view detailed information about the warning condition. Flashing Reserved for future use. Solid The device detects a warning condition. You can connect the device to a computer, and use the AIS 800 setup software to view detailed information about the warning condition. Solid The device is in silent mode or not ready to transmit. NOTE: The AIS 800 device does not transmit without a GPS signal or an MMSI number, when the AIS base station commands a quiet time, or when the device encounters a critical error. Flashing The device is sending an AIS message. Flashing The device is receiving an AIS message. Solid The device is ready to transmit and receive. Solid When these four LEDs are illuminated, the device is connected only to a computer for programming by a USB cable. NMEA 0183 Sentences Supported Sentence ACA ALR GGA RMC SSD TXT VDM VDL VER VSD Definition AIS Regional Channel Assignment Message Set alarm state Glocal positioning system fix data Recommended minimum specific GNSS data AIS ship static data Text transmission, general purpose AIS VHF data-link message AIS VHF data-link own-vessel report Version AIS voyage static data Testing for Interference from LED Lights LED lighting from sources such as navigation lights, searchlights, floodlights, interior and exterior lights, and adornments can interfere with your AIS 800 device. Radio interference can cause poor reception, jam radio signals, and create a safety hazard in emergency situations. You should test for LED interference before mounting the VHF antenna. 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 3