Garmin GHP 10V Marine Autopilot System Installation Instructions
Garmin GHP 10V Marine Autopilot System Manual
View all Garmin GHP 10V Marine Autopilot System manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GHP 10V Marine Autopilot System manual content summary:
- Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 1
Support. NOTE: There is an installation checklist on the last page of these instructions helm unattended. Always be prepared to promptly regain manual control of your boat. Learn to operate the boats. See the Important Safety and Product Information guide in the product box for product warnings and - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 2
Table of Contents GHP™ 10V Installation Instructions 1 Registering Your Device 1 Contacting Garmin 1 Important Safety Information 1 GHP 10V Package Contents 12 Manually Running the Automated Configuration Procedures..........12 Manually Running the Sea Trial Wizard 12 Manually Defining - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 3
the CCU (page 8). This cable can also be used to connect the GHC 20 to optional NMEA 0183-compatible devices (page 10). GHP 10V Installation Instructions 3 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 4
, male ➎ NMEA 2000 terminator, female NMEA 2000 Extension Cables NMEA 2000 extension cables are available if needed. Contact your local Garmin dealer or Garmin Product Support for ordering information. 4 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 5
: There is an installation checklist on the last page of these instructions. Remove the last page and refer to the checklist as you proceed the keys on the GHC 20. • The mounting surface must be strong enough to support the weight of the GHC 20 and protect it from excessive vibration or shock. • The - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 6
20 data cable. The orange and blue wires from this cable must be connected to the alarm (page 7). ➑ GHP 10V Autopilot Gateway 6 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 7
you plan to access the Volvo multilink bus. 2. Secure the Autopilot Gateway with cable ties or other appropriate mounting hardware (not included). GHP 10V Installation Instructions 7 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 8
plan to mount the GHC 20. The flush-mount template is included in the product box, not in these instructions. The flush-mount template has adhesive on the back. 2. Remove the protective liner from the adhesive on the on until turned off by the primary GHC 20. 8 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 9
enough, you can use a drop cable up to 20 ft. (6 m) long (not included). 6. Connect the drop cable to the to the CCU. GHP 10V Installation Instructions 9 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 10
0183. NMEA 0183 Connection Considerations • To identify the Transfer (Tx) A(+) and B(-) wires for your NMEA 0183-compatible device, consult the installation instructions for your device. • When connecting NMEA 0183 devices with two transmitting and two receiving lines, it is not necessary for the - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 11
line. 2. Select Begin, and continue to drive in a straight line. 3. When instructed, turn the boat slowly clockwise, taking care to make the turn as steady and an option: • If the autotune completed successfully, select Done and take manual control of the boat. • If the autotune failed, adjust the - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 12
, select Menu > Setup > Dealer Autopilot Configuration > Automated Setup. 3. Select Autotune, Calibrate Compass, or Set North. 4. Follow the on-screen instructions. Manually Running the Sea Trial Wizard The Sea Trial Wizard allows you to quickly define all of the important configuration settings on - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 13
to a common ground. > > ➊ GHC 20 ➋ NMEA 2000 network (provides power to the GHC 20) ➌ 12 VDC power source ➍ NMEA 0183-compatible device GHP 10V Installation Instructions 13 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 14
Track Error Navigation Data GNSS Sats in View Wind Data The GHP 10V and the GHC 20 are NMEA 2000 certified. 14 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 15
Configuration Settings Although all of the configuration is typically completed automatically through wizard, you can manually adjust any setting (page 12). NOTE: Depending upon the configuration of the autopilot, When set to off, data integrity is compromised. GHP 10V Installation Instructions 15 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 16
during normal operation of the GHP 10V. See the configuration section of the GHC 20 Owner's Manual for more information. Error and Warning Messages Error Message Cause Autopilot Action Autopilot is not The value specified in the low voltage alarm menu. 16 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 17
CCU Mounting Template ➊ ➊ Up, when installing on a vertical surface GHP 10V Installation Instructions 17 - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 18
- Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 19
and use it to assist with the GHP 10V installation process. Read all installation instructions before installing the GHP 10V. Contact Garmin Product Support if you have any questions during the installation process. 1. Refer to the diagram and notes starting on page 6 to understand the necessary - Garmin GHP 10V Marine Autopilot System | Installation Instructions - Page 20
must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Garmin reserves the right to change or improve
GHP 10V Installation Instructions
1
GHP
™
10V Installation Instructions
To obtain the best possible performance and to avoid damage to your
boat, install the Garmin
®
GHP 10V marine autopilot system according
to the following instructions. Professional installation of the autopilot
system is highly recommended.
The GHP 10V is compatible with C3 or newer Volvo
®
EVC systems.
Contact Volvo for more information on updating older EVC systems.
Read all installation instructions before proceeding with the
installation.
If you experience difficulty during the installation, contact
Garmin Product Support.
NOTE:
There is an installation checklist on the last page of these
instructions. Remove the last page and refer to the checklist as you
proceed through the GHP 10V installation.
Registering Your Device
Help us better support you by completing our online registration today.
•
Go to
.
•
Keep the original sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to each
component of your GHP 10V system in the spaces provided on
page 3
.
The serial numbers are located on a sticker on each component.
Contacting Garmin
Contact Garmin Product Support if you have any questions while using
your GHP 10V.
In the USA, go to
www.garmin.com/support
, or contact Garmin USA
by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to
www.garmin.com/support
and click
Contact Support
for in-country support information, or contact Garmin (Europe) Ltd. by
phone at +44 (0) 870.8501241.
Important Safety Information
WARNINGS
You are responsible for the safe and prudent operation of your
vessel.
The GHP 10V is a tool that will enhance your capability to
operate your boat. It does not relieve you from the responsibility of
safely operating your boat. Avoid navigational hazards and never leave
the helm unattended.
Always be prepared to promptly regain manual control of your boat.
Learn to operate the GHP 10V on calm and hazard-free open water.
Use caution when operating the GHP 10V near hazards in the water,
such as docks, pilings, and other boats.
See the
Important Safety and Product Information
guide in the product
box for product warnings and other important information.
CAUTION
Equipment to be connected to this product should have a fire enclosure
or be provided with a fire enclosure.
Always wear safety goggles, ear protection, and a dust mask when
drilling, cutting, or sanding.
Notice
When drilling or cutting, always check the opposite side of the surface.
Be aware of fuel tanks, electrical cables, and hydraulic hoses.