Garmin GMI 10 Digital Marine Instrument Display Installation Instructions, S/N
Garmin GMI 10 Digital Marine Instrument Display Manual
View all Garmin GMI 10 Digital Marine Instrument Display manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GMI 10 Digital Marine Instrument Display manual content summary:
- Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 1
the best possible performance, install your GMI 10 Marine Instrument according to the following instructions. If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional installer. The GMI 10 will communicate with NMEA 2000- or NMEA - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 2
enough to support the weight of the GMI 10 and protect it from excessive vibration or shock. • Allows room for the routing and connection of the cables. There should be at least a 3 inch (8 cm) clearance behind the case. • layer when the screws are tightened. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 3
more information on NMEA 2000, visit www.garmin.com. Follow the directions and reference the diagrams on page 4 to either connect the GMI 10 to your existing NMEA 2000 network or to external switch. The GMI 10 will drain your battery if it is connected directly. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 4
Male terminator Creating a Basic NMEA 2000 Network Notes: • To add additional sensors to your NMEA 2000 network, follow the instructions included with the sensor. • To learn more about NMEA 2000 and building a NMEA 2000 network, visit www.garmin.com. • The GMI 10 is powered by the NMEA 2000 network - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 5
GMI 10 displays the received data, but cannot transmit the data to another NMEA 0183 device or transmit the data to a NMEA 2000 network. Use the diagrams to wire a NMEA 0183 device to your GMI 10 are used only when wiring the GMI 10 to a Garmin GPS 17/17x antenna. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 6
Request/Acknowledge Group Function Transmit/Receive PGN List Group Function System Time Product Information Vessel Heading Engine Parameters - Dynamic Fluid Level Speed - Water Referenced List Group Function Product Information The GMI 10 is NMEA 2000 certified GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 7
Case Material: Fully gasketed, high-impact plastic alloy, waterproof to IEC 529 IPX7 standards Power GMI 10 power usage: 2.5 W max NMEA 2000 Power Input: 9-16 Vdc NMEA 2000 Load Equivalency Number (LEN): 6 (300 mA) Declaration of Conformity Hereby, Garmin . GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 8
updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. © 2010 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park
GMI 10 Installation Instructions
To obtain the best possible performance, install your GMI 10 Marine Instrument according to the following instructions.
If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional
installer.
The GMI 10 will communicate with NMEA 2000- or NMEA 0183-compatible sensors and devices, and can show
information such as speed, heading, water depth, and fuel information when connected to the appropriate sensors.
Product Registration
Help us better support you by completing our online registration today. Go to
. Keep the original
sales receipt, or a photocopy, in a safe place.
For future reference, write down the serial number assigned to your GMI 10 in the space provided below. The serial
number is located on a sticker on the back of the GMI 10.
Serial number
Contact Garmin
Contact Garmin Product Support if you have any questions while installing or using your GMI 10. In the USA, go to
www.garmin.com/support
, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to
www.garmin.com/support
and click
Contact Support
for in-country support information, or contact
Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.
Packing List and Accessories
Before installing your GMI 10, confirm that your package includes the following items. If any parts are missing, contact
your Garmin dealer immediately.
Standard Package
GMI 10 unit
Protective cover
Flush mount hardware
NMEA 0183 data wiring harness
2 NMEA 2000 T-connectors
2 NMEA 2000 terminators (1 male, 1 female)
1 NMEA 2000 drop cable (2 m)
1 NMEA 2000 power cable (2 m), (3 A fuse)
Installation instructions
•
•
•
•
•
•
•
•
•
Optional Accessories
Additional NMEA 2000 network components
Tools Needed
Jigsaw or 3
17
/
32
in. (90 mm) hole saw,
Drill and drill bits
Center punch and hammer
Scissors
File and sandpaper
Phillips screwdriver
Anti-seize lubricant (optional)
•
•
•
•
•
•
•
•
To install and use your GMI 10
1. Select a location (
page 2
).
2. Flush mount the GMI 10 (
page 2
.
3. Connect the GMI 10 to the sensors and to power (
page 3
).
January 2010
190-01168-02 Rev. A
Printed in Taiwan