Garmin GMR 1224 xHD2 Open Array Radar and Pedestal Installation Instructions - Page 4

Garmin Marine Network Considerations, Radar Operation

Page 4 highlights

4 Connect the power cable to the POWER port on the radar. Connecting Directly to Power WARNING When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product specifications. In addition, connecting the power cable without the appropriate fuse in place will void the product warranty. Some radar models do not require a voltage converter unit. If your model is packaged without a voltage converter, it should be connected directly to power. Item À Á Â Description To the Garmin Marine Network 15 A fuse holder To the boat battery (10 to 32 Vdc) Water ground connection 1 Route the power cable to the radar and boat battery. 2 Connect the power cable to the boat battery. 3 Connect the power cable to the POWER port on the radar. Power Cable Extensions Connecting the power cable directly to the battery is recommended. If it is necessary to extend the cable, the appropriate gauge of wire must be used for the length of the extension. You must use crimp connectors and heat-shrink to create a water-resistant connection. Distance 3 m (9 ft. 10 in.) 5 m (16 ft. 4 in.) 6.5 m (21 ft. 3 in.) 8 m (26 ft. 2 in.) Wire Gauge 3.31 mm² (12 AWG) 5.26 mm² (10 AWG) 6.63 mm² (9 AWG) 8.36 mm² (8 AWG) Grounding the Radar The radar (and voltage converter, if applicable) must be connected to the appropriate type of ground using a 3.31 mm² (12 AWG) copper wire (not included). 1 Route a 3.31 mm² (12 AWG) copper wire to a water ground location and to the radar pedestal. 2 Connect the wire to the ground connector on the pedestal ( ) using the pre-installed crimp connector. 3 Coat the ground screw and crimp connector with marine sealant. 4 4 Connect the other end of the wire to the water ground location on the boat, and coat the connection with marine sealant. 5 Select an option: • If your radar was not packaged with a voltage converter, no further grounding is necessary. • If your radar was packaged with a voltage converter, proceed to step 6. 6 Route a different 3.31 mm² (12 AWG) copper wire to water ground location and to the voltage converter. 7 Loosen a screw on one corner of the voltage converter and secure the copper wire to the screw. 8 Coat the screw and wire on the voltage converter with marine sealant. 9 Connect the other end of the wire to the RF ground location on the boat, and coat the connection with marine sealant. Garmin Marine Network Considerations This device connects to Garmin Marine Network devices to share radar data with compatible devices on the network. When connecting to a Garmin Marine Network device, observe these considerations. • A Garmin Marine Network cable must be used for all Garmin Marine Network connections. ◦ Third-party CAT5 cable and RJ45 connectors must not be used for Garmin Marine Network connections. ◦ Additional Garmin Marine Network cables and connectors are available from your Garmin dealer. • Although it is not recommended, you can use a field- installable connector to create a custom-length Garmin Marine Network cable if necessary. Follow the directions provided with the connector. Radar Operation All functions of this radar are controlled with your Garmin chartplotter. See the Radar section of your chartplotter's manual for operating instructions. To download the latest manual, go to www.garmin.com/support/. Software Update You may need to update the device software when you install the device or add an accessory to the device. Loading the New Software on a Memory Card The device may contain a software-update memory card. If so, follow the instructions provided with the card. If a software update memory card is not included, you must copy the software update to a memory card. 1 Insert a memory card into the card slot on the computer. 2 Go to www.garmin.com/support/software/marine.html. 3 Select Download next to "Garmin Marine Network with SD card." 4 Read and agree to the terms. 5 Select Download. 6 Select Run. 7 Select the drive associated with the memory card, and select Next > Finish. Updating the Device Software Before you can update the software, you must obtain a software-update memory card or load the latest software onto a memory card. 1 Turn on the chartplotter. 2 After the home screen appears, insert the memory card into the card slot. GMR 420/620/1220/2520 xHD2 Series Installation Instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

4
Connect the power cable to the POWER port on the radar.
Connecting Directly to Power
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place will void the product warranty.
Some radar models do not require a voltage converter unit. If
your model is packaged without a voltage converter, it should be
connected directly to power.
Item
Description
À
To the Garmin Marine Network
Á
15 A fuse holder
Â
To the boat battery (10 to 32 Vdc)
Water ground connection
1
Route the power cable to the radar and boat battery.
2
Connect the power cable to the boat battery.
3
Connect the power cable to the POWER port on the radar.
Power Cable Extensions
Connecting the power cable directly to the battery is
recommended. If it is necessary to extend the cable, the
appropriate gauge of wire must be used for the length of the
extension.
You must use crimp connectors and heat-shrink to create a
water-resistant connection.
Distance
Wire Gauge
3 m (9 ft. 10 in.)
3.31 mm² (12 AWG)
5 m (16 ft. 4 in.)
5.26 mm² (10 AWG)
6.5 m (21 ft. 3 in.)
6.63 mm² (9 AWG)
8 m (26 ft. 2 in.)
8.36 mm² (8 AWG)
Grounding the Radar
The radar (and voltage converter, if applicable) must be
connected to the appropriate type of ground using a 3.31 mm²
(12 AWG) copper wire (not included).
1
Route a 3.31 mm² (12 AWG) copper wire to a water ground
location and to the radar pedestal.
2
Connect the wire to the ground connector on the pedestal
(
) using the pre-installed crimp connector.
3
Coat the ground screw and crimp connector with marine
sealant.
4
Connect the other end of the wire to the water ground
location on the boat, and coat the connection with marine
sealant.
5
Select an option:
If your radar was not packaged with a voltage converter,
no further grounding is necessary.
If your radar was packaged with a voltage converter,
proceed to step 6.
6
Route a different 3.31 mm² (12 AWG) copper wire to water
ground location and to the voltage converter.
7
Loosen a screw on one corner of the voltage converter and
secure the copper wire to the screw.
8
Coat the screw and wire on the voltage converter with marine
sealant.
9
Connect the other end of the wire to the RF ground location
on the boat, and coat the connection with marine sealant.
Garmin Marine Network Considerations
This device connects to Garmin Marine Network devices to
share radar data with compatible devices on the network. When
connecting to a Garmin Marine Network device, observe these
considerations.
A Garmin Marine Network cable must be used for all Garmin
Marine Network connections.
Third-party CAT5 cable and RJ45 connectors must not be
used for Garmin Marine Network connections.
Additional Garmin Marine Network cables and connectors
are available from your Garmin dealer.
Although it is not recommended, you can use a field-
installable connector to create a custom-length Garmin
Marine Network cable if necessary. Follow the directions
provided with the connector.
Radar Operation
All functions of this radar are controlled with your Garmin
chartplotter. See the Radar section of your chartplotter's manual
for operating instructions. To download the latest manual, go to
www.garmin.com/support/
.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
Loading the New Software on a Memory Card
The device may contain a software-update memory card. If so,
follow the instructions provided with the card. If a software
update memory card is not included, you must copy the software
update to a memory card.
1
Insert a memory card into the card slot on the computer.
2
Go to
www.garmin.com/support/software/marine.html
.
3
Select
Download
next to “Garmin Marine Network with SD
card.”
4
Read and agree to the terms.
5
Select
Download
.
6
Select
Run
.
7
Select the drive associated with the memory card, and select
Next
>
Finish
.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1
Turn on the chartplotter.
2
After the home screen appears, insert the memory card into
the card slot.
4
GMR 420/620/1220/2520 xHD2 Series Installation Instructions