Home » Garmin Manuals » Marine GPS » Garmin STRIKER 4 Portable Bundle » Manual Viewer

Garmin STRIKER 4 Portable Bundle Owners Manual - Page 13

My sonar does not work

View all Garmin STRIKER 4 Portable Bundle manuals

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

To check the voltage, measure the female power and ground sockets of the power cable for DC voltage. If the voltage is less than 10 Vdc, the device will not turn on. My sonar does not work • Push the transducer cable all the way into the back of the device. Even if the cable seems to be connected, you should push firmly so that it is fully seated. • Check to make sure the sonar transmission is turned on. Troubleshooting 9

Section	Page
Table of Contents	3
Introduction	5
Device Overview	5
Contacting Garmin®‎ Product Support	5
Zooming on the STRIKER 4	5
Panning on the STRIKER 4	5
Adjusting the Backlight	5
Adjusting the Color Mode	5
Setting the Beeper	5
GPS Satellite Signal Acquisition	5
Home Screen	5
Customizing the Home Screen	5
Adding a New Layout to the Home Screen of the STRIKER 5 or 7	5
Adding a Custom Layout to the Home Screen of the STRIKER 4	6
Adding the Numbers Screen	6
Numbers	6
Adding the Data Graphs Screen	6
Data Graphs	6
Sonar	6
Full Screen Sonar	6
DownVü Sonar View	6
SideVü Sonar View	6
Split-Screen Frequency	7
Flasher	7
Split-Zoom View	7
Selecting the Transducer Type	7
Creating a Waypoint on the Sonar Screen Using Your Present Location	7
Pausing the Sonar	7
Creating a Waypoint on the Sonar Screen Using a Different Location	7
Overlay Number Settings	7
Sonar Gain and Noise Settings	7
Setting the Gain Manually	7
Setting the Gain Automatically	7
Hiding Surface Noise	8
Interference	8
Setting the Interference	8
Adjusting the Range of the Depth Scale	8
Adjusting the Zoom	8
Locking the Screen to the Water Bottom	8
Setting the Bottom Search Limit	8
Sonar Frequencies	8
Selecting Frequencies	8
Creating a Frequency Preset	8
Setting the Scroll Speed	8
Showing and Adjusting the Depth Line	9
Configuring the Appearance of Suspended Targets	9
Turning on the A-Scope	9
Waypoints	9
Marking Your Present Location as a Waypoint	9
Creating a Waypoint at a Different Location	9
Editing a Saved Waypoint	9
Marking and Navigating to a Man Overboard Location	9
Navigating to a Waypoint	9
Measuring Distance on the Waypoint Map	9
Deleting a Waypoint or an MOB	9
Deleting All Waypoints	9
Routes	10
Creating and Navigating a Route Using the Waypoint Map	10
Editing a Saved Route	10
Viewing a List of Routes	10
Browsing for and Navigating a Saved Route	10
Deleting a Saved Route	10
Deleting All Saved Routes	10
Track	10
Setting the Color of the Track	10
Clearing the Track	10
Managing the Track Log Memory During Recording	10
Configuring the Recording Interval of the Track Log	10
Deleting All Saved Waypoints, Routes, and Tracks	10
Device Configuration	10
System Settings	10
System Information	11
Waypoint Map Settings	11
Sonar Alarms	11
System Alarms	11
Navigation Alarms	11
Navigation Settings	11
My Vessel Settings	11
Unit Settings	11
Setting the Water Temperature Offset	11
Setting the Keel Offset	12
Restoring the Factory Default Settings	12
Appendix	12
Registering Your Device	12
Specifications	12
Software License Agreement	12
Troubleshooting	12
My device does not turn on	12
My sonar does not work	13