Gateway MT6841 8511725 - Gateway Service Guide

Gateway MT6841 Manual

Get Gateway MT6841 PDF manuals and user guides View all Gateway MT6841 manuals
Add to My Manuals
Save this manual to your list of manuals

Gateway MT6841 manual content summary:

  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 1
    GATEWAY NOTEBOOK SERVICEGUIDE ®
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 2
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 3
    discharge 5 Tape 5 Preparing the notebook 6 Removing the battery 6 Adding or replacing memory modules 7 Replacing the DVD drive 11 Replacing the cooling assembly 14 Replacing the processor 19 Replacing the IEEE 802.11 wireless card 22 Replacing the hard drive 26 Replacing the keyboard
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 4
    Contents ii
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 5
    the notebook • Adding or replacing memory modules • Replacing the DVD drive • Replacing the cooling assembly • Replacing the processor • Replacing the IEEE 802.11 wireless card • Replacing the hard drive • Replacing the keyboard cover • Replacing the keyboard • Replacing the CMOS battery • Replacing
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 6
    notebook's general maintenance, technical support, safety notices, and regulatory notices, see the notebook's user guide. Tip If you have suggestions regarding the content of this guide, send an e-mail with the subject "Service Guide Comments" to [email protected]. Use this service guide
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 7
    www.gateway.com Identifying components Use this chart to identify the main components of the notebook. For a complete list of replaceable parts, see "Contents" on page i. LCD panel assembly (see page 38) Keyboard cover (see page 29) Keyboard (see page 31) Cooling assembly (see page 11) Processor (
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 8
    remove it. • Use bright lighting to make part identification easier. • Keep your work surface free from clutter and dust that may damage components. • Use a magnetized screwdriver for removing screws. • When removing components that are attached to the notebook by a cable, unplug the cable before
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 9
    gateway.com Preventing static electricity discharge Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off the notebook, remove the battery on the notebook, follow these guidelines: • Avoid static-causing surfaces such as carpeted floors, plastic, and packing
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 10
    voltages and moving parts, turn off the notebook, remove the battery, and unplug the drive does not contain a disc. 2 Disconnect all peripheral devices and remove any PC Cards and memory cards. 3 Turn off the notebook and unplug the power cord, modem cable, and network cable. 4 Remove the battery
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 11
    .com Adding or replacing memory modules Important Use only memory modules designed for this Gateway notebook. Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 1 black (keyboard) Memory bay To add or replace memory modules: 1 Complete the steps in
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 12
    Replacing Notebook Components 2 Remove the keyboard screw. Tip The screw hole is marked with a K. Keyboard screw 3 Loosen the six memory bay cover screws (these screws cannot be removed). Tip Depending on your model, not all screws may be captive. Screws Screws 8
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 13
    www.gateway.com 4 Use the thumb notch to lift the memory bay cover, then remove it. Be careful not to break off the tabs located on the end of the cover opposite of the thumb notch.
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 14
    Replacing Notebook Components 6 Pull the memory module out of the slot. 7 Hold the new or replacement module at a 30-degree angle and press it into the empty memory slot. This module is keyed so it can only be inserted in one direction. If the module does not fit, make sure that the notch
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 15
    www.gateway.com Replacing the DVD drive Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 1 black (keyboard) 1 black (DVD drive) To replace the DVD drive: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the keyboard screw. Tip The
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 16
    Replacing Notebook Components 3 Loosen the six memory bay cover screws (these screws cannot be removed). Tip Depending on your model, not all screws may be captive. Screws Screws 4 Use the thumb notch to lift the memory bay cover, then remove it. Be careful not to break off the tabs located on the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 17
    bay by pushing on the DVD bracket. DVD bracket 7 Slide the new DVD drive into the drive bay. Make sure that the drive fits securely in the bay. 8 Secure the DVD drive with the screw removed in Step 5. 9 Replace the memory bay cover, then tighten the cover screws. 10 Replace the keyboard screw. Tip
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 18
    Replacing Notebook Components Replacing the cooling assembly Tools you need to complete this task: black (keyboard) To replace the cooling assembly: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the keyboard screw. Tip The screw hole is marked with a K. Keyboard screw 14
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 19
    www.gateway.com 3 Loosen the six memory bay cover screws (these screws cannot be removed). Tip Depending on your model, not all screws may be captive. Screws Screws 4 Use the thumb notch to lift the memory bay cover, then remove it. Be careful not to break off the tabs located on the end of
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 20
    Replacing Notebook Components 5 Loosen the three or four screws (these screws cannot be removed) that secure the cooling assembly to the system board. Use the numbers stamped
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 21
    www.gateway.com 6 .At the same time as you lift, move the cooling assembly away from the side of the notebook, then remove it. The cooling assembly cable is attached to the system board at this point. Be CPU die. 10 Plug in the new cooling fan. 11 Insert the new cooling assembly into the notebook. 17
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 22
    Replacing Notebook Components 12 Tighten the three or four screws, in numerical order, in the holes tighten them in numerical order. Important The number of screws varies by model. 13 Replace the memory bay cover, then tighten the cover screws. 14 Replace the keyboard screw. Tip The screw hole is marked
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 23
    www.gateway.com Replacing the processor Tools you need to complete this task: Phillips black (keyboard) To replace the processor: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the cooling assembly by following the instructions in "Replacing the cooling assembly" on page 14. 19
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 24
    Replacing Notebook Components 3 Use a flat-blade screwdriver to turn the processor lock screw ¼-turn counter-clockwise. -ORUse a flat-blade screwdriver to turn the processor lock screw ½-turn counter-clockwise. You will hear a click when the processor lock is unlocked. 20
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 25
    www.gateway.com 4 Remove the old processor from the system board. 5 Install the new processor onto the system board making grease on the processor. Use only enough to cover the CPU die. 8 Replace the cooling assembly by following the instructions in "Replacing the cooling assembly" on page 14. 21
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 26
    the IEEE 802.11 wireless card Caution By law, only approved wireless modules provided by Gateway, or a Gateway authorized representative, explicitly for this Gateway notebook may be installed in this notebook. Caution Legal requirements dictate the wireless cover be in place during any and all
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 27
    www.gateway.com 2 Loosen the wireless bay cover screw (this screw cannot be removed), then remove the wireless bay cover. Screw 3 Unplug the two antenna cables. 4 Move the antenna cables out of the way. 23
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 28
    Replacing Notebook Components 5 If the wireless card is held by clips, press outward on the clip at each side of the card until the card tilts up. -ORIf the wireless card is held by a screw, remove the screw. Screw 24
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 29
    www.gateway.com 6 Pull the old card out of the slot. 7 Hold the new card at a 30-degree angle and slide it into the empty slot. This
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 30
    the hard drive Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 2 black (hard drive kit) 4 chrome (hard drive cover) Hard drive kit To replace the hard drive: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the two hard drive kit
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 31
    www.gateway.com 3 Slide the old hard drive kit out of the notebook. 4 If the hard drive shipped to you already attached to a new cover, go to Step 8. -OR- If the hard drive shipped to you without a new cover, remove the four screws that secure the hard drive to the hard drive bay cover. Screws
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 32
    Replacing Notebook Components 5 Remove the cover from the old drive. 6 Place the new drive, label side up, onto the cover so the screw holes line up. 7 Replace the screws that secure the cover to the drive. 8 Slide the new hard drive kit into the notebook, then replace the kit screws. 28
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 33
    .gateway.com Replacing the keyboard cover Tools you need to complete this task: Flat-blade driver - OR - Phillips #0 screwdriver Screws removed during this task: Scribe or non-marring tool 2 black (keyboard cover) To replace the keyboard cover: 1 Complete the steps in "Preparing the notebook
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 34
    the cover and find no loose spots. The cover should be flat all the way across. Caution If the cover is not correctly replaced, the notebook could be damaged when you try to close the LCD panel. 9 Close the LCD panel. 10 Press down on the hinge covers, then replace the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 35
    -blade driver - OR - Phillips #0 screwdriver Screws removed during this task: Scribe or non-marring tool 2 black (keyboard cover) 1-3 black (keyboard) To replace the keyboard: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the keyboard cover by following the instructions
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 36
    the LCD panel, turn the notebook over so the bottom is facing up, then loosen the six memory bay cover screws (these screws cannot be removed). Tip Depending on your model, not all screws may be captive. Screws Screws 6 Use the thumb notch to lift the memory bay cover, then remove it. Be
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 37
    www.gateway.com 7 Loosen the wireless bay cover screw (this screw cannot be removed), then remove the wireless bay cover. Screw 8 Remove the two optional keyboard screws. Tip Depending on the keyboard features, one or both of these screws may be absent. Screw Screw 9 Turn the notebook over so the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 38
    or damage any other components. Keyboard connector clip 13 Lift the old keyboard away from the notebook. The keyboard is now completely detached from the notebook. 14 Place the new keyboard keys-down on the notebook with the space bar away from you. 15 Make sure the black keyboard connector clip is
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 39
    gateway the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 29. 20 Turn the notebook over so the bottom is facing up , then replace the keyboard screws removed in Step 8. 21 Replace the memory bay cover and
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 40
    driver - OR - Phillips #0 screwdriver Screws removed during this task: Scribe or non-marring tool 2 black (keyboard cover) 1-3 black (keyboard) To replace the CMOS battery: 1 Complete the steps in "Preparing the notebook" on page 6. 2 Remove the keyboard cover by following the instructions
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 41
    any other components. 6 Plug the new battery into the system board. Important Use only CMOS batteries designed for this Gateway notebook. The non-conductive sleeve and wires are not reusable. 7 Replace the palm rest (if removed) by following the instructions in "Replacing the palm rest" on page
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 42
    the LCD panel assembly: 1 Complete the steps in "Preparing the notebook" on page 6. 2 If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 43
    the notebook. Make sure you grasp the connector, not the cable. Retaining clips Connector 6 Lift up on the video cable retaining clips slightly, then slide the video cable out from under the clips. 7 Taking care to note the cables' routing and positions as they are installed from Gateway, pull
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 44
    8 Remove the four hinge screws that secure the LCD panel to the notebook. Screws 9 Lift the LCD panel assembly away from the notebook. The LCD panel assembly is now completely detached from the notebook. 10 Place the new LCD panel assembly onto the notebook, then replace the four hinge screws. 40
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 45
    .gateway.com 11 Slide the antenna cables through the retaining clips, under the system board, then into the wireless card area. 12 Slide the LCD video cable under the retaining clips, then plug the LCD video connector into the notebook. 13 Close the keyboard compartment by following the instructions
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 46
    Replacing Notebook Components Replacing the LCD panel inverter Tools you need to complete this task: Flat-blade driver - OR - instructions in "Replacing the keyboard" on page 31. Tip You do not need to unplug the keyboard from the notebook. 5 Remove the LCD panel by following the instructions
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 47
    www.gateway.com 6 Remove the four or six rubber inserts from the front of the LCD panel assembly. Rubber insert Rubber insert Rubber insert Rubber insert Rubber
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 48
    Replacing Notebook Components 8 Carefully separate the front and back of the LCD panel assembly. Tip If you only removed the bottom two screws in the previous step,
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 49
    www.gateway.com 10 Unplug both cables from the inverter. 11 Remove the old inverter, front of the LCD panel assembly. 17 Replace the LCD panel assembly onto the notebook by following the instructions in "Replacing the LCD panel assembly" on page 38. 18 Close the keyboard compartment by following the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 50
    Replacing Notebook Components Replacing the LCD panel Tools you need to complete this task: Flat-blade driver - OR - notebook" on page 6. 2 If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 51
    www.gateway.com 6 Remove the four or six rubber inserts from the front of the LCD panel assembly. Rubber insert Rubber insert Rubber insert Rubber insert Rubber
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 52
    Replacing Notebook Components 8 Carefully separate the front and back of the LCD panel assembly. 9 Remove the two screws holding the bracket to the LCD panel assembly, then remove the bracket. Screw Screw 48
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 53
    www.gateway.com 10 Remove the four screws connecting the LCD panel to the LCD panel assembly. Screw Screw 11 Remove the LCD panel from the LCD panel assembly. Screw Screw 49
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 54
    Replace the four or six LCD panel assembly screws. 18 Replace the four or six rubber inserts. 19 Replace the LCD panel assembly onto the notebook by following the instructions in "Replacing the LCD panel assembly" on page 38. 20 Close the keyboard compartment by following the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 55
    the LCD panel assembly lid: 1 Complete the steps in "Preparing the notebook" on page 6. 2 If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 56
    Replacing Notebook Components 6 Remove the four or six rubber inserts from the front of the LCD panel assembly. Rubber insert Rubber insert Rubber insert Rubber insert Rubber
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 57
    www.gateway.com 8 Carefully separate the front and back of the LCD panel assembly. 9 Remove the two screws holding the bracket to the LCD panel assembly, then remove the bracket. Screw Screw 53
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 58
    Replacing Notebook Components 10 Remove the four screws connecting the LCD panel to the LCD panel assembly. Screw Screw 11 Remove the LCD panel from the LCD
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 59
    www.gateway.com 15 Press the front and back of the LCD panel together in several the four or six rubber inserts. 18 Replace the LCD panel assembly onto the notebook by following the instructions in "Replacing the LCD panel assembly" on page 38. 19 Close the keyboard compartment by following the
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 60
    If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 4 Remove the hard drive kit by following the instructions in "Replacing the hard drive" on
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 61
    www.gateway.com 8 Lift the black touchpad connector clip, then remove the touchpad cable. Be careful not to touch or damage any other components. 9 Remove the four screws from the top of the palm rest. Screws 57
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 62
    in "Replacing the keyboard cover" on page 29. 17 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 18 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 19 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 63
    If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 4 Remove the hard drive kit by following the instructions in "Replacing the hard drive" on
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 64
    Replacing Notebook Components 7 Remove the LCD panel by following the instructions in "Replacing the LCD panel assembly" on page 38. 8 Remove the palm rest by following the instructions in "Replacing the palm rest" on page 56. 9 Remove the two screws that secure the modem card to the system board.
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 65
    in "Replacing the keyboard cover" on page 29. 17 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 18 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 19 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 66
    If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 4 Remove the hard drive kit by following the instructions in "Replacing the hard drive" on
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 67
    in "Replacing the keyboard cover" on page 29. 16 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 17 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 18 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 68
    to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Additional materials you may need to complete this task: • X-23-7762 thermal grease Screws removed during this task: 1 black (DVD drive) 2 black (hard drive kit) 1 black (wireless card) Select
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 69
    19. 6 If the notebook has IEEE 802.11 wireless networking built in, remove the IEEE 802.11 wireless card from the old system board and install it on the new system board by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 7 Remove the hard drive kit by following
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 70
    in "Replacing the keyboard cover" on page 29. 22 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 23 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 24 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 71
    If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 5 Remove the hard drive kit by following the instructions in "Replacing the hard drive" on
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 72
    in "Replacing the keyboard cover" on page 29. 18 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 19 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 20 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 73
    If the notebook has IEEE 802.11 wireless networking built in, unplug the antenna cables from the IEEE 802.11 wireless card by following the instructions in "Replacing the IEEE 802.11 wireless card" on page 22. 5 Remove the hard drive kit by following the instructions in "Replacing the hard drive" on
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 74
    in "Replacing the keyboard cover" on page 29. 19 Replace the hard drive kit by following the instructions in "Replacing the hard drive" on page 26. 20 Replace the DVD drive by following the instructions in "Replacing the DVD drive" on page 11. 21 Plug the antenna cables into the IEEE 802
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 75
    .com Copyright © 2006 Gateway, Inc. All rights reserved. Gateway, Gateway Country, the Gateway stylized logo, and the black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. in the United States and other countries. All other brands and product names are trademarks
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 76
    Replacing Notebook Components 72
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 77
  • Gateway MT6841 | 8511725 - Gateway Service Guide - Page 78
    MAN BLADE/OAS SVC GDE R3 12/06
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
®
GATEWAY NOTEBOOK
SERVICE
GUIDE