GE AJCM10DCD Use and Care Manual - Page 20

Install Case In Window, Notes

Get GE AJCM10DCD PDF manuals and user guides View all GE AJCM10DCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation Instructions WINDOW INSTALLATION-OPTIONAL (cont.) 7 INSTALL CASE IN WINDOW A Peel off the backing from the bottom window gasket. B Place the gasket on the stool and over the brackets, even with the rear edge, sticky side down. E With the window closed, mark where the window sash meets the case. F Peel off the backing from the case top gasket. G Hold on to the case, open the window and place the gasket along the mark on the case. Put the gasket on top of the case where the window will close. Bottom window gasket C Carefully slide the empty case into the window until the holes in the case line up with the holes in the panel angles. Case holes H Place the vinyl window gasket over the case top gasket. Insert the panel tabs through the slits in the gasket. Cut the gasket on each side to the width of the window. NOTES: • The case should have a 1/8″ minimum tilt toward the outside. • Be sure the seal gasket and panel gaskets remain in position and do not roll with the case. D Lower the window so it fits behind the panel tabs. Insert the 4 type A screws through the holes in the case and into the panel angles, 2 on each side. Panel tabs Case screws Panel tab Vinyl window gasket I Close the window tightly on the vinyl gasket. Bend the gasket forward to expose the panel tabs. Drill pilot holes into the window sash. Attach the panel tab to the window on each side with a type D screw. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
INSTALL CASE IN WINDOW
Peel off the backing from the bottom window
gasket.
Place the gasket on the stool and over the
brackets, even with the rear edge, sticky
side down.
Carefully slide the empty case into the window
until the holes in the case line up with the holes
in the panel angles.
N
OTES:
•
The case should have a 1/8
″
minimum tilt toward
the outside.
•
Be sure the seal gasket and panel gaskets remain
in position and do not roll with the case.
Lower the window so it fits behind the panel tabs.
Insert the 4 type A screws through the holes in the
case and into the panel angles, 2 on each side.
With the window closed, mark where the window
sash meets the case.
Peel off the backing from the case top gasket.
Hold on to the case, open the window and place
the gasket along the mark on the case.
Place the vinyl window gasket over the case top
gasket. Insert the panel tabs through the slits in
the gasket. Cut the gasket on each side to the width
of the window.
Close the window tightly on the vinyl gasket.
Bend the gasket forward to expose the panel tabs.
Drill pilot holes into the window sash.
Installation Instructions
20
WINDOW INSTALLATION—OPTIONAL (cont.)
7
A
B
C
D
E
F
G
H
I
Bottom window gasket
Case holes
Panel
tabs
Case
screws
Put the gasket on
top of the case
where the window
will close.
Panel tab
Vinyl window gasket
Attach the panel tab
to the window on each side
with a type D screw.