GE GTUP270GMWW Installation Instructions

WARNING

RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instructions.

• Appliance installation must be performed by a qualified installer.

• Install the clothes appliance according to these instructions and in accordance with local

codes. In the absence of local codes, installation must comply with National Fuel Gas

Code, ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code,

CSA B149.1.

•

California Safe Drinking Water and Toxic Enforcement Act.

This act requires the governor of California to publish a list of substances known to the

state to cause cancer, birth defects or other reproductive harm and requires businesses

to warn customers of potential exposure to such substances. Gas appliances can

cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or

LP fuels. Properly adjusted dryers will minimize incomplete combustion. Exposure to these

substances can be minimized further by properly venting the dryer to the outdoors.

• This appliance must be exhausted to the outdoors.

• Use only 4” rigid metal ducting for exhausting the appliance to the outdoors.

•

DO NOT

install a clothes dryer with flexible plastic ducting materials. If flexible metal

(semi-rigid or foil-type) duct is installed, it must be UL listed and installed in accordance

with the instructions found in “Connecting The Dryer To House Vent” on page 8 of this

manual. Flexible venting materials are known to collapse, be easily crushed, and trap lint.

These conditions will obstruct dryer airflow and increase the risk of fire.

• Do not install or store this appliance in any location where it could be exposed to water

and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with the customer).

In the state of Massachusetts, installation must be performed by a qualifiedor

licensed contractor, plumber, or gasfitter qualified or licensed by the state.

Installation

Instructions

Unitized Gas

Washer/Dryer

Questions on Installation? Call: 1-800-GECARES (US)

or Visit our Web site at:

www.GEAppliances.com (US)

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT-

Save these instructions for

local inspector’s use.

•

IMPORTANT-

Observe all

governing codes

and ordinances.

•

Note to Installer -

Be sure to leave these

instructions with the customer.

•

Note to Customer -

Keep these instructions

with your Use and Care Book for future

reference.

• Before the appliance is removed from service

or discarded, remove the washer and dryer

door.

• Inspect the dryer exhaust outlet and straighten

the outlet walls if they are bent.

• Service information and the wiring diagram

are located at the access panel.

• Do not allow children on or in the appliance.

Close supervision of children is necessary when

the appliance is used near children.

• Install the dryer where the temperature is

above 50°F for satisfactory operation of the

dryer control system.

LEVEL

8" PIPE WRENCH

10" ADJUS

TABLE WRENCHES

(x2)

TOOLS YOU

WILL NEED

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

MATERIALS YOU WILL NEED

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

4" DUCT CLAMPS

OR

4" SPRING CLAMPS

(x2)

(x2)

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

4" COVER PLATE (IF NEEDED)

(KIT WE1M454)

189D7219P001

31-16655

10/29/10 GE

D

E

S

I

G

N

C

E

R

T

I

F

I

E

D

PARTS SUPPLIED

2 Rubber Washers

2 Stainer Screens/

Ruuber Washers

(washers may be in water hoses)

2 Washer Hoses

1 Cable Tie

1/4” Nutdriver

GE GTUP270GMWW Installation Instructions

GE GTUP270GMWW Manual

GE GTUP270GMWW manual content summary: