GE JGBS23SEMSS Use and Care Manual - Page 42

Convert to LP Gas, device. The bolts must be properly tightened

Get GE JGBS23SEMSS - 30inch Gas Range PDF manuals and user guides
UPC - 084691165293
View all GE JGBS23SEMSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installation Instructions 7 INSTALL THE ANTI-TIP DEVICE (cont.) D For wood construction, drill a pilot hole at an angle of 20° from the horizontal. A nail or awl may be used if a drill is not available. Mount the Anti-Tip device with the screw provided. For cement or concrete construction, you will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware. Wallboard Anti-Tip device Back of range Wood screw WHEN ALL HOOKUPS ARE COMPLETED Make sure all controls are left in the OFF position. Make sure the flow of combustion and ventilation air to the range is unobstructed. CONVERT TO LP GAS (or convert back to natural gas from LP) This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer. The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator. Keep these instructions and the orifices in case you want to convert back to natural gas. Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware. E Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward. The bracket should stop the range within 4 inches. If it does not, the bracket must be reinstalled. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
42
WHEN ALL HOOKUPS ARE COMPLETED
Make sure all controls are left in the OFF
position. Make sure the flow of combustion and
ventilation air to the range is unobstructed.
CONVERT TO LP GAS (or convert back to
natural gas from LP)
This range leaves the factory set for use with
natural gas. If you want to convert to LP gas, the
conversion must be performed by a qualified LP
gas installer.
The conversion instructions and LP orifices can be
found attached to the range next to the pressure
regulator.
Keep these instructions and the orifices in case
you want to convert back to natural gas.
Installation Instructions
INSTALL THE ANTI-TIP DEVICE (cont.)
For wood construction, drill a pilot hole at an
angle of 20° from the horizontal. A nail or awl
may be used if a drill is not available.
Mount the Anti-Tip device with the screw
provided.
For cement or concrete construction, you
will need a 1/4
″
x 1
1
⁄
2
″
lag bolt and a 1/2
″
O.D.
sleeve anchor, which are not provided. Drill the
recommended size hole for the hardware.
Install the sleeve anchor into the drilled
hole and then install the lag bolt through the
device. The bolts must be properly tightened
as recommended for the hardware.
Slide the range against the wall, and check for
proper installation by grasping the front edge
of the cooktop and carefully attempting to tilt
the range forward. The bracket should stop
the range within 4 inches. If it does not, the
bracket must be reinstalled.
E
D
7
Back of
range
Wallboard
Wood screw
Anti-Tip
device