GE NX-108E User Manual
GE NX-108E - Security NetworX NX-4 System Manual
 |
UPC - 782136402414
View all GE NX-108E manuals
Add to My Manuals
Save this manual to your list of manuals |
GE NX-108E manual content summary:
- GE NX-108E | User Manual - Page 1
GE Security NetworXTM Series NX-108/116/124E LED keypad User manual g imagination at work - GE NX-108E | User Manual - Page 2
NX-108/116/124E User manual Page 2 10/11/05 - GE NX-108E | User Manual - Page 3
ABORT FEATURE (OPTIONAL) ...11 BYPASSING ZONES ...11 GROUP BYPASS...11 UNBYPASSING ...11 TURNING THE DOOR CHIME ON AND OFF...11 ADDING AND CHANGING USER CODES ...12 ASSIGNING USER CODE AUTHORITY LEVELS ...13 OTHER KEYPAD FUNCTIONS ...14 SETTING THE KEYPAD TONE ...14 CHANGE PARTITION (OPTIONAL)...14 - GE NX-108E | User Manual - Page 4
INTRODUCTION This manual is furnished to help you understand your security system and become proficient in its operation. All users of your security system should read and follow the instructions in this booklet and, if possible, practice on the keypad control while your professional installer is on - GE NX-108E | User Manual - Page 5
that allows you to turn on (ARM) the security system by pressing either the [STAY] or [EXIT] key on the keypad control (for ARMING only) as programmed by the installing company. A four (4) or six (6) digit entry code used to arm or disarm the system. NX-108/116/124E User manual Page 5 10/11/05 - GE NX-108E | User Manual - Page 6
is flashing in order to prevent an alarm. The user may then rearm the system and exit before the delay expires.) A steady fire light means a fire zone has been faulted. A rapidly flashing fire light means that a fire zone is in a trouble condition. NX-108/116/124E User manual Page 6 10/11/05 - GE NX-108E | User Manual - Page 7
"on" if the security system requires service. If the service light is "on, press the [*] key followed by the [2] key to determine the service condition. One or more zone lights will illuminate indicating what service(s) is required. Call your service provider immediately for these problems. Below is - GE NX-108E | User Manual - Page 8
: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. Check with your installing company to determine how your security system will respond to the Panic/HoldUp activation. NX-108/116/124E User manual Page 8 10/11/05 - GE NX-108E | User Manual - Page 9
. Restore power if possible. If not, contact your installing company for service. • If the power light is flashing, you have a battery failure. Contact your installing company for service. Enter your 4 or 6 digit user code. (Optional, if programmed.) NX-108/116/124E User manual Page 9 10/11/05 - GE NX-108E | User Manual - Page 10
allow the user to arm the security system without entering a user code. Quick all designated interior zones. This is only possible if programmed by your installer ("bypass toggle the designated Entry/Exit doors, the keypad control will sound a solid tone NX-108/116/124E User manual Page 10 10/11/05 - GE NX-108E | User Manual - Page 11
zones: Step 1 Press the [BYPASS] key. Step 2 Enter user code, if required (optional). The bypass light flashes. Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass. (Example: Press the [1] key for zone 1, press [1] [2] for zone 12 sound. NX-108/116/124E User manual Page 11 10/11/05 - GE NX-108E | User Manual - Page 12
you are back at Step 4 above. If the code is rejected, the sounder will beep 3 times. If another "user code" needs to be programmed, return to Step 5. Press the [#] key while the ready light is flashing to exit the User Code Programming Mode. NX-108/116/124E User manual Page 12 10/11/05 - GE NX-108E | User Manual - Page 13
other codes) 5 Arm/Disarm 6 Bypass Zones 7 Open / Close Reporting 8 If this user number to assign authority level. Repeat Steps 4 - 8 until you have assigned authority levels to all user numbers. Press the [#] key to exit the Assigning Authority Level Program. NX-108/116/124E User manual - GE NX-108E | User Manual - Page 14
will be performed as programmed. Step 2 If the siren test is performed, enter a user code to silence the siren. No alarms will be sent and no reports will be sent unless a communicator test is performed, at which time a test signal will be sent. NX-108/116/124E User manual Page 14 10/11/05 - GE NX-108E | User Manual - Page 15
Zone Troubles. Your system must be Disarmed to use the Reset function. Step 1 Step 2 Press [r]-[7]. Resets have now been performed. The FIRE light will go off if the smoke detectors have been reset. If the keypad after would be entered [0] - [7]. NX-108/116/124E User manual Page 15 10/11/05 - GE NX-108E | User Manual - Page 16
any zone(s) are 12 hours. Entering a valid code will silence the keypad sounder when it is pulsing. The arm/disarm state of your system will not change when entering a code to silence a pulsing keypad sounder. Please contact your installer if a trouble condition exists. NX-108/116/124E User manual - GE NX-108E | User Manual - Page 17
______ zones Programmed functions: Abort delay Battery test Cancel alarm Change partitions (LED) Chime Communicator test Manual fire alarm Manual medical alarm Manual panic alarm Forced arming Group bypass Quick arm Re Exit Service Light/Message enabled Siren test NX-108/116/124E User manual - GE NX-108E | User Manual - Page 18
Zone descriptions Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16 Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24 NX-108/116/124E User manual Page 18 10/11/05 - GE NX-108E | User Manual - Page 19
www.gesecurity.net EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT ©2005 © GE Security EMEA bvba. All rights reserved. GE Security EMEA bvba grants the right to reprint this manual for internal use only. GE Security EMEA bvba reserves the right to change information without notice
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
 |
 |
GE
Security
NetworX
TM
Series
NX-108/116/124E LED keypad
User manual
g
imagination at work