GE PSB2200NBB Quick Specs - Page 2
GE Profile Advantium, Wall Oven - installation
UPC - 084691171157
View all GE PSB2200NBB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
PSB2200N GE Profile Advantium® 240 Wall Oven Preparation with an Accessory Drawer Prepare the opening The Advantium 240V can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation. Single Advantium 240V Installation: Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown. * For existing cutouts, a maximum width of 28-1/2" 30" 23-1/2" is acceptable. If the opening is slightly wider, secure a furring strip on each side of 25-1/4" Min. the cutout for securing the oven. • Always maintain 36-3/4" minimum height from the floor to the cutout in any single or combined installation. • Allow 3/4" to 2-1/8" case 21" 5" min. from floor 1" min. above toekick Construct Base Min. 3/8" Plywood Supported by 2x4 or 2x2 Runners all Four Sides trim overlap on the sides and 7/8" overlap on the bottom of the opening for all models. The amount of overlap on the sides depends on the actual cutout width. Allow 1-1/4" case trim overlap on the top for models PSB2200 and PSB2201 and for models ZSC2200, ZSC2201 and ZSC2202. • Oven overlaps will conceal cut edges on all sides of the opening. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. Prepare the opening (cont.) When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium 240V and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides. • the support must be level and rigidly mounted, flush with the bottom edge of tIhnsetacllauttioonuotv. er a GE/Monogram Warming Drawer: 30" 23-1/2" Construct Solid Bottom Min. 3/8" Plywood Supported 25-1/4" by 2x4 or 2x2 Min. Runners all Four Sides 21" 2" Min. (3" recommended) 5" min. from floor 1" min. above toekick Per warming drawer requirement * For existing cutouts, a maximum width of 28-1/2" is acceptable. If the opening is slightly wider, secure a furring strip on each side of the cutout for securing the oven. Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. Installation over a GE/Monogram Oven and Warming Drawer: Warming Drawer: Construct Solid 30" 23-1/2" Bottom Min. 3/8" Plywood Supported by 2x4 or 2x2 Runners all 25-1/4" Four Sides Min. 21" 2" Min. (3" recommended) 5" min. from floor 1" min. above toekick Per Oven Requirement 2" Min. Per warming drawer requirement * For existing cutouts, a maximum width of 28-1/2" is acceptable. If the opening is slightly wider, secure a furring strip on each side of the cutout for securing the oven. Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. Caution: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up to 50 pounds or a total weight of 160 pounds. Listed by Underwriters Laboratories Specification Created 9/08 240442