Gigabyte B365M D3H User Manual - Page 43

A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode, CSM Support

Page 43 highlights

A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode If the SATA controller has been configured in Intel RST Premium With Intel Optane System Acceleration mode, please follow the steps below: 1. After system restarts, go to the BIOS Setup, make sure CSM Support under the BIOS menu is disabled. 2. Go to Peripherals\SATA And RST Configuration and make sure Use RST Legacy OROM is disabled. If you want to enable the Optane™ memory installed in the M2A connector, set PCIe Storage Dev On Port 9 to RST Controlled. 3. Enter the operating system, launch the Intel® Rapid Storage Technology utility from the Start menu, and then enable Intel® Optane™ Memory on the Intel® Optane™ Memory screen. 4. Then select which drive to be accelerated. Click Yes to continue. Follow the on-screen instructions to proceed. When completed, restart the system. 5. Launch the Intel® Rapid Storage Technology utility from the Start menu and make sure the Intel® Optane™ Memory has been enabled. If you want to accelerate the system drive, you can select specific folders, files, or applications to accelerate using the Intel® Optane™ Memory Pinning function. (The Intel® Optane™ memory used must have at least 32 GB capacity.) •• An Optane™ memory cannot be used to accelerate an M.2 PCIe SSD. •• Do not abruptly remove the Optane™ memory. Doing so will cause the operating system to stop functioning correctly. •• If you want to change/remove the Optane™ memory, you must disable it using the Intel® Rapid Storage Technology or Intel(R) Optane™ Memory application first. •• After enabling the Optane™ memory, the related BIOS settings will remain even after a BIOS update. - 43 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47

A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode
If the SATA controller has been configured in Intel RST Premium With Intel Optane System Acceleration mode,
please follow the steps below:
1. After system restarts, go to the BIOS Setup, make sure
CSM Support
under the
BIOS
menu is disabled.
2. Go to
Peripherals\SATA And RST Configuration
and make sure
Use RST Legacy OROM
is disabled. If
you want to enable the Optane
memory installed in the M2A connector, set
PCIe Storage Dev On Port 9
to
RST Controlled
.
3. Enter the operating system, launch the Intel
®
Rapid Storage Technology utility from the Start menu, and then
enable Intel
®
Optane
Memory on the
Intel
®
Optane
Memory
screen.
4. Then select which drive to be accelerated. Click
Yes
to continue. Follow the on-screen instructions to proceed.
When completed, restart the system.
5. Launch the
Intel
®
Rapid Storage Technology
utility from the Start menu and make sure the Intel
®
Optane
Memory has been enabled. If you want to accelerate the system drive, you can select specific folders, files, or
applications to accelerate using the
Intel
®
Optane
Memory Pinning
function. (The Intel
®
Optane
memory
used must have at least 32 GB capacity.)
An Optane
memory cannot be used to accelerate an M.2 PCIe SSD.
Do not abruptly remove the Optane
memory. Doing so will cause the operating system to stop
functioning correctly.
If you want to change/remove the Optane
memory, you must disable it using the Intel
®
Rapid
Storage Technology or Intel(R) Optane
Memory application first.
After enabling the Optane
memory, the related BIOS settings will remain even after a BIOS update.
- 43 -