Gigabyte GA-B75M-D2P Manual - Page 13

SATA3 0 SATA 6Gb/s Connector, SATA2 1/2/3/4/5 SATA 3Gb/s Connectors, F_PANEL Front Panel Header

Get Gigabyte GA-B75M-D2P PDF manuals and user guides View all Gigabyte GA-B75M-D2P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

5) SATA3 0 (SATA 6Gb/s ConDnEBeUcGtor) DEBUG DEBUG DEBUG DEBUG The SATA connector conformsPtOoRST ATA 6GbP/OsRsTtandard PaOnRdTare comPpOaRtiTble with SPAOTRAT 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. 1 7 SATA3 0 Pin No. 1 2 3 4 Definition GND TXP TXN GND Pin No. 5 6 7 Definition RXN RXP GND 6) SATA2 1/2/3/4/5 (SATA 3Gb/s Connectors) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. 1 7 SATA2 5 4 3 2 1 Pin No. 1 2 3 4 Definition GND TXP TXN GND Pin No. 5 6 7 Definition RXN RXP GND 7) F_PANEL (Front Panel Header) Connect the power switch, reset switch, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power Switch Power LED 10 9 NC PW- RES+ PW+ RES- PLED- HD- PLED+ HD+ 21 Reset Switch Hard Drive Activity LED •• PLED Power LED: System Status LED S0 On S3/S4/S5 Off Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 •• PW (Power Switch): sleep state or powered off (S5). Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information). •• HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. •• RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. •• NC: No connection. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. - 13 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
- 13 -
5)
SATA3 0 (SATA 6Gb/s Connector)
The SATA connector conforms to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device.
6)
SATA2 1/2/3/4/5 (SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device.
SATA3
0
SATA2
5
4
3
2
1
7
7
1
1
Pin No.
Definition
Pin No.
Definition
1
GND
5
RXN
2
TXP
6
RXP
3
TXN
7
GND
4
GND
Pin No.
Definition
Pin No.
Definition
1
GND
5
RXN
2
TXP
6
RXP
3
TXN
7
GND
4
GND
7)
F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
•
PW
(Power Switch):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your
system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more
information).
•
HD
(Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
•
RES
(Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
•
NC
: No connection.
•
PLED
Power LED:
System Status
LED
S0
On
S3/S4/S5
Off
Connects to the power status
indicator on the chassis front
panel. The LED is on when the
system is operating. The LED is
off when the system is in S3/S4
sleep state or powered off (S5).
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch,
power LED, hard drive activity LED and etc. When connecting your chassis front panel module to this header,
make sure the wire assignments and the pin assignments are matched correctly.
1
2
9
10
NC
PLED-
PW-
PLED+
PW+
HD-
RES+
HD+
RES-
Power Switch
Hard Drive
Activity LED
Power
LED
Reset
Switch