Gigabyte GA-F2A75-D3H User Manual - Page 70

B. Configuring SATA controller mode in BIOS Setup

Get Gigabyte GA-F2A75-D3H PDF manuals and user guides View all Gigabyte GA-F2A75-D3H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Step 1: Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Make sure OnChip SATA Controller is enabled. To enable RAID for the SATA3 0/1/2/3 connectors, set OnChip SATA Type to RAID. To enable RAID for the SATA3 4/5 connector, set OnChip SATA Type to RAID and set OnChip SATA Port4 Type to As SATA Type (Figure 1). Step 2: Save changes and exit BIOS Setup. Figure 1 The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. Appendix - 70 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Appendix
- 70 -
The BIOS Setup menus described in this section may differ from the exact settings for your mother-
board. The actual BIOS Setup menu options you will see shall depend on the motherboard you have
and the BIOS version.
Step 2:
Save changes and exit BIOS Setup.
Figure 1
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Make
sure
OnChip SATA Controller
is enabled. To enable RAID for the SATA3 0/1/2/3 connectors, set
OnChip
SATA Type
to
RAID
. To enable RAID for the SATA3 4/5 connector, set
OnChip SATA Type
to
RAID
and set
OnChip SATA Port4 Type
to
As SATA Type
(Figure 1).