Gigabyte GA-Z68X-UD4-B3 Manual - Page 51
F_USB30 Controller Etron EJ168 USB Controller, USB 3.0/2.0 ports routed to the
UPC - 818313012661
View all Gigabyte GA-Z68X-UD4-B3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 51 highlights
When a Cable Problem Occurs... If a cable problem occurs on a specified pair of wires, the Status field will show Short and then length shown will be the approximate distance to the fault or short. Example: Part1-2 Status = Short / Length = 2m Explanation: A fault or short might occur at about 2m on Part 1-2. Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Status fields will show Open, and the length shown is the approximate length of the attached LAN cable. Onboard LAN Boot ROM Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip. (Default: Disabled) R_USB30 Controller (Etron EJ168 USB Controller, USB 3.0/2.0 ports on the back panel) Enables or disables the Etron EJ168 USB controller. (Default: Enabled) R_USB30 Turbo (Etron EJ168 USB Controller, USB 3.0/2.0 ports on the back panel) Enables or disables the Turbo USB mode for the Etron EJ168 USB controller. The actual performance may vary depending on the number of devices being installed. (Default: Disabled) F_USB30 Controller (Etron EJ168 USB Controller, USB 3.0/2.0 ports routed to the on- board F_USB30 header) Enables or disables the Etron EJ168 USB controller. (Default: Enabled) GSATA3 Controller (Marvell 88SE9172 Chip, GSATA3_6 and GSATA3_7 connectors) Enables or disables the SATA controller integrated in the Marvell 88SE9172 chip. (Default: Enabled) GSATA3 Ctrl Mode (Marvell 88SE9172 Chip, GSATA3_6 and GSATA3_7 connectors) Enables or disables RAID for the SATA controller integrated in the Marvell 88SE9172 chip or configures the SATA controller to AHCI mode. IDE Configures the SATA controller to IDE mode. (Default) AHCI Configures the SATA controller to AHCI mode. Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug. RAID Enables RAID for the SATA controllers. eSATA3 Controller (Marvell 88SE9172 Chip, eSATA connectors on the back panel) Enables or disables the SATA controller integrated in the Marvell 88SE9172 chip. (Default: Enabled) eSATA3 Ctrl Mode (Marvell 88SE9172 Chip, eSATA connectors on the back panel) Enables or disables RAID for the SATA controller integrated in the Marvell 88SE9172 chip or configures the SATA controller to AHCI mode. IDE Configures the SATA controller to IDE mode. (Default) AHCI Configures the SATA controller to AHCI mode. Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug. RAID Enables RAID for the SATA controllers. Onboard Serial Port 1 Enables or disables the serial port and specifies its base I/O address and corresponding interrupt. Options are: Auto, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled. - 51 - BIOS Setup