Haier LET32A300 User Manual - Page 30

Reference s

Get Haier LET32A300 PDF manuals and user guides View all Haier LET32A300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Using the features Press button to select the content you recorded. Press the button to display the program information. Press button to cancel. Press OK or PLAY/PAUSE button to play the program recorded and press STOP button to stop it. Note O Changing the channel will not influence the recording in the same frequency, but will influence the time shift. When the recorded program is being played, you can not delete it. O Press the INDEX button repeatedly, the program will be displayed in the order of program name, channel name, program time, file name and file length. Reference Sections Troubleshooting To assist in location of possible faults use the help guide below: No picture, no sound Verify if the television is properly plugged in. Verify if the television has a proper supplied power source. Verify if electricity is available. Blank screen No sound Poor sound No picture in some channel No color for some channel program (black and white) Spots with some or all pictures Television out of control Verify if correct signals are input. Operate the remote to change signal input to correct input. Restart the television if power supply is interrupted. Press MUTE button and verify if Mute mode is set. Switch to other channel and verify if the same problem happens. Press VOL+ button to see if the problem can be solved. Verify if sound system is correct. Refer to user's manual for adjustment. Verify if correct channel is selected. Adjust the antenna. Verify if the same problem exists in other channels. Check out of picture and sound systems. Refer to relative instructions in the Manual for color adjustment. Verify if the antenna is correctly connected. Verify if the antenna is in good condition. Make fine adjustment of channel. Disconnect the television from power supply and 10 seconds later, connect the television to the power supply. If the problem still exists, contact authorized after-sales service for technical assistance. Note O If the fault can not be repaired using the above guide consult with your local authorized service centre. O The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire. EN-29 Digital LED LCD Television Instruction Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Using the features
EN-29
Digital LED LCD Television Instruction Manual
Press
²³
button to select the content you recorded.
Press the
±
button to display the program
information.
Press
´
button to cancel.
Press
OK
or
PLAY/PAUSE
button to play the
program recorded and press
STOP
button to stop it.
Note
Changing the channel will not influence the
recording in the same frequency, but will influence
the time shift. When the recorded program is being
played, you can not delete it.
Press the
INDEX
button repeatedly, the program
will be displayed in the order of program name,
channel name, program time, file name and file
length.
Reference Sections
Troubleshooting
To assist in location of possible faults use the
help guide below:
No picture, no
sound
Verify if the television is
properly plugged in.
Verify if the television has a
proper supplied power source.
Verify if electricity is available.
Blank screen
Verify if correct signals are
input.
Operate the remote to change
signal input to correct input.
Restart the television if power
supply is interrupted.
No sound
Press
MUTE
button and verify if
Mute mode is set.
Switch to other channel and
verify if the same problem
happens.
Press
VOL+
button to see if the
problem can be solved.
Poor sound
Verify if sound system is correct.
Refer to user‘s manual for
adjustment.
No picture in
some channel
Verify if correct channel is
selected.
Adjust the antenna.
No color for
some channel
program
(black and
white)
Verify if the same problem exists
in other channels.
Check out of picture and sound
systems.
Refer to relative instructions
in the Manual for color
adjustment.
Spots with
some or all
pictures
Verify if the antenna is correctly
connected.
Verify if the antenna is in good
condition.
Make fine adjustment of
channel.
Television out
of control
Disconnect the television from
power supply and 10 seconds
later, connect the television
to the power supply. If the
problem still exists, contact
authorized after-sales service
for technical assistance.
Note
If the fault can not be repaired using the above
guide consult with your local authorized service
centre.
The TV set must only be repaired by a qualified
registered service person. Never attempt to
remove the back cover as the TV set has dangerous
voltages in side that may cause a fatally or fire.