Hamilton Beach HBH450 Operation Manual - Page 2
Save These Instructions - uk
UPC - 040094909353
View all Hamilton Beach HBH450 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
GB IMPORTANT SAFETY INSTRUCTIONS WARNING - When using electrical appliances, basic safety precautions should be followed, including the following: • Read the Operation Manual before using blender. Keep Operation Manual handy. • Before first use, wash container assembly in hot, soapy water. Do NOT place in dishwasher. • Plug into a grounded outlet. • Do not remove ground. • Do not use an adapter. • Do not use an extension cord. • Disconnect power before cleaning or servicing. • To reduce risk of personal injury, unplug cord from outlet when not in use, and before putting on or taking off parts. • Unplug the blender and inspect the power cord insulation for cracks on a weekly basis. Refer to "Technical Service" for repair or replacement. • To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid. • Do not spray the base with a high-pressure spray gun. • Extreme caution must be used when moving an appliance containing hot oil or other hot liquids. • Do not use appliance for other than intended use. • Not intended for use by or near children. • This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. • To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly, DO NOT insert utensils into blender container while operating blender. • Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on. • To prevent possibility of serious personal injury, keep hands out of blender container while operating blender. Always operate blender with container cover in place. • Avoid contacting moving parts. Switch off the appliance and disconnect from power supply before changing accessories or approaching parts that move in use. • Blades are sharp. Handle carefully. • If cutter assembly blades are loose, discontinue use immediately and replace cutter assembly. Do not attempt to repair or tighten cutter assembly. • Inspect container and cutter assembly daily. Do not use broken, chipped, or cracked container. Check cutter for wear, nicks, or broken blades. Do not use broken, loose, or cracked cutting blades. • Do not use outdoors. • This appliance is intended for short periods of operation, with a rated operating time of 3 minutes. • Do not leave blender unattended while it is operating. • To prevent damage to blender, container, or cutter assembly, DO NOT move or shake blender while in operation. If blending action stops during operation, turn blender OFF (O), remove container from base, remove container cover, and use a thin rubber spatula to push mixture towards cutters. • When blending hot liquids, remove center-piece of two-piece lid. Hot liquids may push lid off jar during blending. To prevent possible burns: Do not fill blender jar beyond the 1 quart (1 liter) level. With the protection of an oven mitt or thick towel, place one hand on top of lid. Keep exposed skin away from lid. Start blending at lowest speed. • Always operate blender with container cover in place. • This blender is designed with motor overload protection. If the motor stops during operation due to overheating, unplug the unit and allow it to cool down for 15 minutes. Plug unit back after 15 minutes to resume normal operation. • The normal function of this product may be disturbed by strong electromagnetic interference. If this occurs, simply reset the product and resume normal operation by following the operation manual. If normal operation cannot be resumed, place the product in a different location. • Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Refer to "Technical Service" for instructions on examination, repair, or electrical or mechanical adjustment. • If the supply cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. UK ONLY: If fitted with a non-rewirable U.K. plug, the 13 amp fuse approved by ASTA to be B.S. 1362 must be used. If you need a replacement fuse carrier, it must be replaced with the same colour coded carrier with the same markings. Fuse covers and carriers can be obtained from approved service agents. - SAVE THESE INSTRUCTIONS - 2