Harman Kardon AVR 1600 Owners Manual - Page 35

ADVANCED FUNCTIONS NOTES: •It is not necessary to program the remote to control your DVD player's transport controls while the AVR, VID2 or VID3 devices are in use, as the remote is preprogrammed at the factory with this function. •When in DVD device mode, the remote may be used to control either a DVD player or a Harman Kardon Blu-ray Disc player. To toggle between these two device modes, press and hold the DVD Input Selector until it flashes. The factory default is to operate a Harman Kardon Blu-ray Disc player. To program punch-through control while operating any device: 1. Press and hold the Input Selector (or AVR selector) for the main device the remote will be operating until the Program LED flashes and the remote enters Program mode. 2. Select the type of punch-through programming. a) Volume Control: Press the Volume Up Button. b) Channel Control: Press the Volume Down Button. c) Transport Control: Press the Play Button. 3. Press the Input Selector (or AVR Selector) for the device whose volume, channel or transport controls you would like to be active while operating the device you selected in the first step. The LED will flash green to confirm the programming. For example, if you wish to watch your TV (programmed into the Video 3 Button) while changing channels using your cable box (Video 2), first press and hold the Video 3 Button until the LED flashes. Then press the Volume Down Button, followed by the Video 2 Button. To undo punch-through programming, follow the same steps as above, but press the same Input (or AVR) Selector in Steps 1 and 3. You may reassign the transport control punch-through programming for the AVR, VID2 and VID3 devices to other devices, such as CD. If you wish to remove transport control punch-through altogether for the AVR, VID2 or VID3 device, follow the same procedure as for programming punch-through, but in Step 3 press either of the other two of these three special selector buttons. For example, to remove punch-through transport control from the VID3 device so that pressing any of the transport controls will have no effect, press and hold the VID3 Button until the Program Indicator LED flashes in amber, then press the Play Button, followed by either the AVR or VID2 Button. Macros Macros are used to program sequences of up to 19 commands that are executed with a single button press. Macros are well suited for power on and off commands, or to send out a favorite multidigit channel number with one button press, or to have the ability to send out a code sequence to control a device while the remote is operating another device, but with more flexibility than the built-in punch-through controls. Some commands may not be programmed into macros: Mute, Dim, or Channel Up/Down. NOTE: Use caution when programming complicated macros. It isn't possible to program a pause or delay before sending commands after Power On, and the component may not be ready to respond to commands instantaneously after powering on. To program, or "record", a macro, follow the steps below. 1. Simultaneously press one of the four Macro Buttons, or the Power On Button, and the Mute Button to enter program mode. 2. Press the Input (or AVR) Selector for each device before you enter commands to be transmitted to that device. This step counts as one of the 19 commands allowed for each macro. 3. For the Power On command, DO NOT press the Power On Button. Press the Mute Button instead. 4. Press the Power Off Button to program the Power Off command. 5. Press the Sleep Button to end the programming process. To execute the macro, press the Macro Button, or the Power On Button, selected in the first step of programming the macro. It isn't possible to "edit" a command within a macro. However, you may erase the macro as follows: 1. Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the LED flashes. 2. Press the Channel Down Button to erase the macro. Resetting the Remote To reset the remote to its factory defaults, simultaneously press and hold any Input Selector and the "0" Numeric Key. When the Program LED flashes in amber, enter the code "333". When the green LED goes out, the remote will have been fully reset. PROCESSOR RESET If the unit behaves erratically after a power surge, first turn off the Main Power Switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the receiver on. If this doesn't help, reset the AVR. NOTE: A system reset erases all user configurations, including Source settings, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the appendix worksheets. To reset the AVR 1600, place it in Standby mode (press the frontpanel Standby/On Switch so that the Power Indicator turns amber). Then press and hold the front-panel Surround Mode Button for at least 5 seconds until the RESET message appears. If the receiver does not function correctly ofter a processor reset, contact an authorized Harman Kardon service center for assistance. Authorized service centers may be located by visiting the Web site at www.harmankardon.com. MEMORY If the AVR 1600 is unplugged or experiences a power outage, it will retain user settings for up to four weeks. 35